Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 45

Страница: 45 / 156

ELECTRICAL INSTALLATION

Control Circuit Connections

Temperature Protection or PID Control with PT-100 or PTC Sensor:

•

Connect the sensor Positive wire to the AFM2 terminal. Place the AFM2
micro switch in the

DOWN

position.

•

Connect the sensor Negative wire to the ACM terminal.

•

Use a jumper wire to connect the AFM2 and AVI1 terminals. The AVI1 micro
switch should be in the

position.

•

Any shield wire should be connected to Earth ground.

For specific parameter setups, please call Technical Support.

Speed Control using 0-10 VDC Potentiometer:

•

Connect the potentiometer Positive wire to the VFD +10V terminal.

•

Connect the potentiometer Output wire to the AVI1, AVI2, or ACI terminal.
The AVI1 micro switch should be in the

position. If using the ACI termi

nal, the ACI micro switch should be

DOWN

•

Connect the potentiometer Com wire to the ACM terminal (signal ground).

•

Any shield wire should be connected to Earth ground.

•

AVI1 Input Select [IO–05]

ACI Input Select [IO–00]

should be set to

0-10V

•

Auto Speed Reference [SET–07]

Hand Speed Reference [SET–09]

should be set to

the chosen input.

Содержание Cerus X-Drive





























































































































































Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды

Franklin Electric Cerus X-Drive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды