Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 105

Страница: 105 / 156

MAINTENANCE

Troubleshooting

105

IGBT over heat (oH1)

• IGBT temperature exceeds

protection level

• Ensure that the ambient temperature falls within the specified

temperature range.

• Make sure that the ventilation holes are not obstructed.
• Remove any foreign objects from the heatsinks and check for

possible dirty heat sink fans.

• Check the fan and clean it.
• Provide enough spacing for adequate ventilation.

InrCom Time Out (ictE)

• Internal communication time-out • Check Comm card installation

• Check communications settings
• Check wiring and grounding for possible interference

Internal BT (CardiBTc)

• Bluetooth card error

• Check card installation and [Comm-30] Comm Card ID

Lv at accel (LvA)

• DC BUS voltage is less than PROT-

03 during acceleration

• Check if the input voltage is normal
• Check for possible sudden load
• Adjust setting of PROT-03

Lv at decel (Lvd)

• DC BUS voltage is less than PROT-

03 during deceleration

• Check if the input voltage is normal
• Check for possible sudden load
• Adjust setting of PROT-03

Lv at normal SPD (Lvn)

• DC BUS voltage is less than PROT-

03 in constant speed

• Check if the input voltage is normal
• Check for possible sudden load
• Adjust setting of PROT-03

Lv at stop (LvS)

• DC BUS voltage is less than PROT-

03 at stop

• Check if the input voltage is normal
• Check for possible sudden load
• Adjust setting of PROT-03

MC Fault (ryF)

• Electromagnet switch error.

Electric valve switch error when
executing Soft Start. (Frame E
and above.)

• Do not disconnect RST when drive is still operating.

Motor overheat (oH3)

• The internal temperature of the

VFD exceeds the setting of PROT-
20 (PTC level) or PROT-31 (PT100
level 2).

• Make sure that the motor is not obstructed.
• Ensure that the ambient temperature falls within the specified

temperature range.

• Change to a higher power motor.

No Flow (NOFL)

• No water flow (pump application) • Refer to

“No Flow Protection” on page 78

oc at accel (ocA)

• Over current during acceleration.

Output current exceeds 2.4 rated
current during acceleration.

• Short-circuit at motor output: Check for possible poor insulation at

the output.

• Acceleration Time too short: Increase the Acceleration Time.
• VFD output power is too small for the application.

oc at decel (ocd)

• Over current during decelration.

Output current exceeds 2.4 rated
current during deceleration.

• Short-circuit at motor output: Check for possible poor insulation at

the output.

• Acceleration Time too short: Increase the Acceleration Time.
• VFD output power is too small for the application.

oc at normal SPD (ocn)

• Over current at normal speed.

Output current exceeds 2.4 rated
current during constant speed.

• Short-circuit at motor output: Check for possible poor insulation at

the output.

• Acceleration Time too short: Increase the Acceleration Time.
• VFD output power is too small for the application.

oc at stop (ocS)

• Over-current at stop. Hardware

failure in current detection

• Please call technical support.

oc HW error (Hd1)

• Over-current detection error

• Reboots the power. If fault code is still displayed on the keypad,

please call technical support.

occ HW error (Hd3)

• IGBT short-circuit detection when

power is ON

• Reboots the power. If fault code is still displayed on the keypad,

please call technical support.

Over load (OL)

• Overload

•

Fault

Description

Corrective Action

Содержание Cerus X-Drive





























































































































































Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды

Franklin Electric Cerus X-Drive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды