Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 103

Страница: 103 / 156

MAINTENANCE

Troubleshooting

103

MAINTENANCE

Troubleshooting

Error Messages:

When the drive detects a fault or warning, an error message displays on the

screen showing the current problem condition. In some cases the fault can be cleared by
pressing the Stop/Reset button.

Fault Records:

In addition, the drive records up to 30 of the most recent faults. These can be

accessed by pressing the

key. Use the arrow keys to scroll through the list. For more infor

mation about a selected fault, press the

Enter

key to display details about the occurrence,

including date, time, output frequency, output current, and other related data.

NOTE:

Fault records can also be located through

[PROT-51 to 56]

, or by pressing

Menu/Back/Down/

Fault

Using the displayed fault title, refer to the following table for troubleshooting details.

Diagnostic Fault Codes

Fault

Description

Corrective Action

Analog current input loss (ACE)

• ACI loss

• Check the ACI wiring
• Check if the ACI signal is less than 4mA

Auto-tuning error (AUE)

(AUE 1-4)

• Error during motor auto tuning
• No feedback current
• Motor phase loss
• No load current
• Leakage inductance

• Restart tuning
• Check motor capacity and parameter settings
• Accel/Decel times too short
• Check cabling between drive and motor

Braking fault (bF)

• Brake resistor fault

• If the fault code is still displayed on the keypad after pressing

“RESET” key, please call technical support.

Broken Pipe (BKPI)

• Low pressure with high frequency • Check piping for leaks

• Verify parameter settings

CAN bus Add Err (CAdE)

• CANopen station address error

• Reset address

CAN bus Index Err (CIdE)

• CANopen index error

• Reset index

CAN bus off (CbFE)

(CFrE)

• CANopen bus off error
• CANopen memory error

• Check Comm card installation
• Check communications settings
• Check wiring and grounding for possible interference
• Make sure communication circuit is wired in series
• For CFrE error, reset parameters and station address

cc HW error (Hd0)

• Current Clamp detection error

• Cycle the power. If fault code is still displayed on the keypad, please

call technical support.

CPU Trap 0 error (TRAP)

• CPU instruction error

•

Содержание Cerus X-Drive





























































































































































Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды

Franklin Electric Cerus X-Drive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды