Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 101

Страница: 101 / 156

ACCESSORIES

Optional Extension Cards

101

Setup Optional Ethernet Communication Card

Install the card following the instructions in

“Extension Card Installation” on page 97

Verify card detection.
•

Check

Com Card ID [COMM–30]

to determine whether a Communications Card has been installed

and recognized by the drive. A value of

No Com Card

indicates that a card has not been detected.

•

To activate the card in the drive, set

Comm Card [COMM–55]

2h (bit 1 on)

. This will detect the

installed card and automatically change

[COMM–30]

Ethernet/IP

2. Download card values to the drive.

•

Set

MBus Card Reset [COMM–52]

1_Enable

. This populates default values from the card into the

appropriate drive parameters. For example:
–

IP Address: 192.168.1.5 to

[COMM–38 through 41]

–

Address Mask: 255.255.255.0 to

[COMM–42 through 45]

–

Gateway Address: 192.168.1.1 to

[COMM–46 through 49]

• When complete,

[COMM–52]

will automatically return to

0_Disable

3. Adjust settings as required for the network and upload to card.

•

Use

[COMM–38 through 49]

to set each address segment.

•

When complete, set

MBus TCP Config [COMM–53]

2_I-net Par On

. This loads the new addresses

to the card, enabling communication with the network.

Содержание Cerus X-Drive





























































































































































Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды

Franklin Electric Cerus X-Drive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды