Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 140

Страница: 140 / 156

PARAMETER REFERENCE TABLES

Parameter Descriptions > Motor Menu

140

Motor-15 2319 Y Torque Filter T

0.001 to 10 Sec

Response time in controlling torque to motor.

Motor-16 2320 Y Slip Filter T

0.001 to 10 Sec

Response time in controlling slip compensation.

Motor-17 2321 Y Torque Cmp Gain 0 to 10*

Gain value for output voltage increase to compensate for voltage drop on

stator resistance at high motor loads in torque compensation function.

For PM motors max value is 5000.

Motor-18 2322 Y Slip Cmp Gain

0 to 10

Gain value for output frequency increase to provide slip compensation at

high motor loads

Motor-19 2323 Y Slip Dev Level

0 to 100%

Slip percentage level to cause over slip trip. Setting of 0 is No Detection.

Motor-20 2324 Y Slip Dev Det T

0 to 10 Sec

Duration slip percentage has to be at before causing over slip trip.

Motor-21 2325 Y Over Slip Trip

0_Alarm and Run

1_Alarm and Decel

2_Alarm and Coast

3_Disabled

Operation when over slip trip occurs.

Motor-22 2326 Y Motor Hunt Gain 0 to 10000

Gain value in detecting shaft speed of a synchronous motor. A sudden

load change can cause shaft speed to fluctuate.

Motor-23 2327 Y Auto restart

0 to 6000 sec

If the number of internal faults defined by [Prot-41] occurs within this

duration, then an auto restart of the VFD will occur.

Motor-24 2328 Y I/F Current

0 to 150%

Percentage of nominal motor current [SET-03] used to regulate AC out

put current during I/F control and DC current during PM DC Alignment.

Motor-25 2329 Y PM Bandwidth HS 0 to 600 Hz

Allowable frequency bandwidth around desired frequency in order to

adjust operating frequency to prevent vibrations in motor operation.

Motor-26 2330 Y PMSVC Fltr Gain

0 to 655.35 Sec

Gain value in adjusting the operating frequency from the desired fre

quency to prevent vibrations in motor operation.

Motor-27 2331 Y Freq I/F to PM

0 to 599 Hz

When increasing frequency, the frequency to switch modes from I/F

mode to PMSVC mode.

Motor-28 2332 Y Freq PM to I/F

0 to 599 Hz

When decreasing frequency, the frequency to switch modes from PMSVC

mode to I/F mode.

Motor-29 2333 Y I/F fltr time

0 to 6 Sec

Low-pass filter time of current being commanded from I/F Current

[Motor-24].

Motor-30 2334 Y Angle Det Pulse

0 to 3

Value is a multiplier of nominal motor current which is magnitude of pulse

during the angle detection. This is only used when Rotor Zeroing [Motor-

14] is set to 2 or 3.

Motor-31 2335 Y Zero voltage T

0 to 60 Sec

Duration the output is 0V to establish a static startup. Once the system is

at a static startup. The VFD can accurately estimate angles. This parame

ter is applicable when SS Normal Start [Prot-42] is not set to 0.

Motor-32 2336 Y Injection Freq

0 to 1200 Hz

Frequency used to determine angle of motor during High Frequency

Injection. Injection Frequency should be at least 100Hz larger than motor's

nominal frequency. Carrier frequency should be 10 times larger than Injec

tion Frequency.

Motor-33 2337 Y Injection V

0 to 200 V

Voltage used to determine angle of motor during High Frequency Injec

tion.

Motor-34 2338 N Run Time Min

0 to 1439 min

Minutes of the motor run time. Less than 60 seconds is not recorded.

Motor-35 2339 N Run Time Days

0 to 65535 day

Days of the motor run time.

Motor-36 2340 N Motor PF

0 to 1

Power Factor value from motor nameplate

Motor-37 2341 N PM Trq Comp I/F 0 to 5000

PM Torque Compensation in I/F Mode

Motor-38 2342 N PM Trq Comp SVC 0 to 5000

PM Torque Compensation in SVC Mode

Motor-39 2343 N DC-Tun Curr P

0 to 65535

Gain value regulating DC current during DC Alignment of PM motor.

Motor-40 2344 N DC-Tun Curr I

0 to 65535

Integral gain regulating DC current during DC Alignment of PM motor.

CODE

Mod

Bus AR

Display Name

Range

Description

Содержание Cerus X-Drive





























































































































































Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды

Franklin Electric Cerus X-Drive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды