Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 43

Страница: 43 / 156

ELECTRICAL INSTALLATION

Control Circuit Connections

Example Configurations

4-20mA Speed Control Signal from an External BMS or PLC:

•

Connect the BMS or PLC output signal to the ACI or AVI1 terminal. The ACI
micro switch should be in the

position. If using the AVI1 terminal, the

AVI1 micro switch should be

DOWN

•

Connect the BMS Com wire to the ACM terminal (signal ground).

•

Any shield wire should be connected to Earth ground.

•

ACI Input Select [IO–00]

AVI1 Input Select [IO–05]

should be set to the correct

signal type.

•

Auto Speed Reference [SET–07]

should be set to the chosen input.

0-10V Speed Control Signal from an External BMS or PLC:

•

Connect the BMS or PLC output signal to the AVI1, AVI2, or ACI terminal.
The AVI1 micro switch should be in the

position. If using the ACI termi

nal, the ACI micro switch should be

DOWN

•

Connect the BMS Com wire to the ACM terminal (signal ground).

•

Any shield wire should be connected to Earth ground.

•

AVI1 Input Select [IO–05]

ACI Input Select [IO–00]

should be set to

0-10V

•

Auto Speed Reference [SET–07]

should be set to the chosen input.

4-20mA Transducer with VFD 10 VDC Power:

•

Connect the transducer positive (Ppower) wire to the VFD +10V terminal.

•

Connect the transducer output (Out) wire to the ACI or AVI1 terminal. The
ACI micro switch should be in the

position. If using the AVI1 terminal,

the AVI1 micro switch should be

DOWN

•

Any shield wire should be connected to Earth ground.

•

ACI Input Select [IO–00]

AVI1 Input Select [IO–05]

should be set to the correct

signal type.

•

Auto Speed Reference [SET–07]

should be set to

PID Output

PID Feedback Source

[SET–18]

should be set to the chosen input, and

PID Feedback Units [SET–19]

should be set to the appropriate

scale (psi, temp, flow, etc.).

4-20mA Transducer with VFD 24 VDC Power:

•

Connect the transducer positive (Power) wire to the VFD +24V terminal.

•

Connect the transducer output (Out) wire to the ACI or AVI1 terminal. The
ACI micro switch should be in the

position. If using the AVI1 terminal,

the AVI1 micro switch should be

DOWN

•

Use a jumper wire to connect the ACM and DCM terminals.

•

Any shield wire should be connected to Earth ground.

•

ACI Input Select [IO–00]

AVI1 Input Select [IO–05]

should be set to the correct

signal type.

•

Auto Speed Reference [SET–07]

should be set to

PID Output

PID Feedback Source [SET–18]

should be set to the cho

sen input, and

PID Feedback Units [SET–19]

should be set to the appropriate scale (psi, temp, flow, etc.).

Содержание Cerus X-Drive





























































































































































Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды

Franklin Electric Cerus X-Drive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды