Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 18

Страница: 18 / 156

PHYSICAL INSTALLATION

Mounting the Drive

The mounting location should have nearby access to the electrical supply and access to the motor wiring.
Refer to

Use lag screws or bolts appropriate for supporting the weight of the drive.
1.

Mount the drive using the mounting holes on the back side of the drive enclosure.

2. Screws at the top must attach to a solid structure such as a stud or brace.
3. All screw hole locations should be used to ensure the drive is securely mounted.

IMPORTANT:

Do not drill holes in the drive.

When removing large drives from the pallet, use suitable lifting equipment connected to the lifting holes at
the top outer edges of the drive.
1.

Use a spreader bar the same width as the drive so
the lifting cables are straight up and down.

2. Slowly lift the drive from the pallet.
3. Use lifting equipment to place the drive in the

desired installation location.

Risk of bodily injury or damage to drive or other equipment.

•

The drive should be mounted on a structure such as a wall or post capable of supporting the weight
of the unit. Refer to

“Specifications” on page 141

for drive weight.

•

Install VFD on a non-combustible surface.

•

Ensure suitable mounting hardware is used when installing the drive.

•

Do not install the drive on unreinforced drywall.

•

Use suitable lifting equipment, in good condition, rated for at least 5 times the weight of the drive.

Содержание Cerus X-Drive





























































































































































Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды

Franklin Electric Cerus X-Drive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды