Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 156

background image

ELECTRICAL INSTALLATION

Wiring Guidelines

33

ELECTRICAL INSTALLATION

Wiring Guidelines

1.

Mount the drive as close as possible to the service entrance panel. Connect directly to the service
entrance, not to a sub-panel.

2. Use a dedicated branch circuit for the drive. Verify that the circuit is equipped with a properly-sized cir

-

cuit breaker or fuse.

3. Separate input power and motor wiring by at least 8 in. (20.3 cm).
4. Cross over other branch circuits and facility wiring at a 90



angle. If necessary to run wires in parallel,

separate by at least 8 in. (20.3 cm).

5. All control wiring—sensors, switches, transducers, etc.—should be in a separate conduit routed individ

-

ually, not parallel, from high voltage wiring. In addition, any shielded cables should be properly
grounded.

6. Treat Open-Delta power configuration (two-transformer utility bank) as single-phase power and size

VFD and power wiring accordingly.

7. Install a line reactor for VFDs in pump systems with dedicated service transformer to protect VFD from

transient power surges and provide some degree of harmonics distortion mitigation.

Power Wires

Motor Wires

ض

ض

ض

ض

ض

Risk of damage to VFD

,

or malfunction can occur.

Follow all wire routing and grounding instructions carefully. Inductive currents caused by parallel wiring,
or close proximity between high voltage and control wiring can cause unexpected behaviors.
•

Do not run input power and motor wires in the same conduit.

•

Do not run motor wires from multiple VFDs in common conduit.

•

Do not run control wiring parallel with high voltage wiring.

•

Do not run VFD wiring parallel with building or facility wiring.

•

Do not use aluminum wires for VFD connections.

•

Do not install power factor correction capacitors, surge suppressors, or RFI filters on the VFD output.

•

Do not install a magnetic contactor or disconnect in the motor circuit.

•

Do not leave wire fragments, metal shavings or other metal objects inside the VFD.

•

Improper splicing or damage to motor cable insulation may expose the conductor(s) to moisture and
can produce motor cable failure.

•

For retrofit application, check the integrity of power and motor leads. This requires measuring the
insulation resistance with a suitable megohm-meter.

«
...
31
32
33
34
35
...
»

Содержание Cerus X-Drive





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cerus X-Drive

Бренд: D+H Страницы: 16

DB1-122D3FN-N2CC

Бренд: Eaton Страницы: 114

Бренд: Sumitomo Страницы: 50

POWERLINK E84DGDV Series

Бренд: Lenze Страницы: 70

Бренд: Kalatec Automacao Страницы: 24

Бренд: Danfoss Страницы: 2

TWIN MASTER 24V

Бренд: UCS Страницы: 8

DL-PS/24-JB-OD-S Series

Бренд: Jesco Страницы: 2

Бренд: Baldor Страницы: 42

Бренд: ABB Страницы: 92

Бренд: ABB Страницы: 210

Бренд: ABB Страницы: 53

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Fortuna IV Series

Бренд: SunStar Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды