Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 156

background image

UNPACKING AND INSPECTION

Transportation and Storage

13

UNPACKING AND INSPECTION

Transportation and Storage

The VFD should be stored in the shipping carton or crate before installation, in a controlled environment
that meets the following requirements:

The performance of capacitors in the drive will degrade if not charged occasionally. It is recommended to
charge a stored drive every 2 years to restore the performance of the capacitors.

NOTE:

If the VFD is kept in storage for longer than 2 years, when powering the drive, use an adjustable AC

power source (ex. AC autotransformer) to charge the drive at 70 to 80% of the rated voltage for 30 minutes
(do not run the drive). Then, charge the drive at 100% of rated voltage for an hour (do not run the drive).

Unpacking

1.

Inspect exterior of package for shipping damage. If there is damage, notify the shipping agent and your
sales representative.

2. Make sure the part number and product ratings on the identification label are correct for the applica

-

tion.

3. When possible, remove the VFD cover and make sure the product ratings on the nameplate match the

package label.

4. The VFD comes in various forms of

shipping crates. If applicable, remove
the top and side fasteners from the
packaging.

Risk of damage to VFD or other equipment.

•

Do not stack VFD boxes higher than standard 48” cube height when palleting for storage.

•

Do not place heavy items on VFD.

•

Do not drop VFD or subject it to hard impact.

•

Dispose of VFD properly as industrial equipment waste.

Storage Temperature

-25 to 70 °C (-13 to 158 °F)

Location

Pollution Degree 2 Environment

Relative Humidity

95% Maximum relative humidity (non-condensing)

Risk of personal injury or damage to VFD or other equipment.

•

Use suitable lifting equipment, in good condition, rated for at least 5 times the weight of the VFD.
Refer to

“Specifications” on page 141

for the weight of each drive by frame size.

«
...
11
12
13
14
15
...
»

Содержание Cerus X-Drive





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cerus X-Drive

Бренд: TQ Страницы: 28

Compax3H C3H1xxV4 Series

Бренд: Parker Страницы: 44

Бренд: IBM Страницы: 20

PARAMAX M Series

Бренд: Sumitomo Drive Technologies Страницы: 24

Бренд: Canworld Страницы: 267

Бренд: BeiJer Страницы: 84

TRINORM 436 Series

Бренд: Emerson Страницы: 6

Бренд: Simu Страницы: 2

Бренд: Leadshine Technology Страницы: 10

Бренд: LSIS Страницы: 3

Бренд: FALK Страницы: 12

Бренд: Küenle Страницы: 56

Бренд: Fagor Страницы: 96

USB2.0CD-RW/DVD-ROM Combo Drive

Бренд: IBM Страницы: 72

Бренд: ZF Страницы: 30

Бренд: UNI Geräte Страницы: 9

Бренд: Parker Страницы: 14

VLT PTC Thermistor Card MCB 112

Бренд: Danfoss Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды