Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 139

Страница: 139 / 156

PARAMETER REFERENCE TABLES

Parameter Descriptions > Motor Menu

139

Parameter Descriptions > Motor Menu

AR = Adjustable while running.

ADV2-27 2075 Y dEb Offset V

0 to 200 V

Decel Energy Backup Error (dEb) Offset Voltage that the DC Bus reduces

by to initiate dEb operation. Varies by VFD Rating.

ADV2-28 2076 Y dEb Mode Select 0_Disable

1_Auto Dec/Stop

2_AutoDec/Restart

Select Decel Energy Backup Error (dEb) operation when DC Bus voltage

drops by ADV2-27. This feature is used to detect power loss.

ADV2-30 2078 Y PID Mode Select 0_Serial PID

1_Parallel PID

0_Serial: VFD uses conventional PID control structure.

1_Parallel: Proportional, Integral, and Derivative gains are independent.

ADV2-31 2079 N PID Unit Format

0_1

1_0.1

2_0.01

Select precision of PID operation.

ADV2-32 2080 N PID Ref Source

0_Keypad

1_AVI1 Analog

2_ACI Analog

3_AVI2 Analog

4_RS485

Select source of PID setpoint.

ADV2-52 2100 Y LD Set Point

SET-19 to (variable)

Adjustable setting for Low Demand pressure set-point from 0 to [Set-20

F/B Max]x 0.95. It can be adjusted to lower or higher than HD (Main) pres

sure set-point value to provide desired pressure and prevent overpressure

trip at pump start in Low Demand situation.

ADV2-53 2101 Y LD Max Freq

SET-23 to SET-22

PID High Frequency Limit setting for Low Demand. Adjust to lower fre

quency setting to prevent overpressure trips during run but enough to

maintain pressure at LD Set-point.

CODE

Mod

Bus AR Display Name

Range

Description

CODE

Mod

Bus AR

Display Name

Range

Description

Motor-00 2304 N Motor A-Tuning

0_None

1_IM Rotating

2_IM No-Rotation

3_SPM No-Rotation

4_IPM No-Rotation

Performs a motor test to measure the motor characteristics. Select motor

type Induction Motor (IM) or Permanent Magnet (PM) motor and if the

motor is allowed to rotate during autotune operation.

Motor-01 2305 N Motor Rs Value

0.0 to 65.535 Ohm

Induction Motor rotor resistance

Motor-02 2306 N Motor Rr Value

0.0 to 65.535 Ohm

Induction Motor stator resistance

Motor-03 2307 N Motor Lm Value

0.0 to 6553.5 mH

Induction Motor rotor inductance

Motor-04 2308 N Motor Lx Value

0.0 to 6553.5 mH

Induction Motor stator inductance

Motor-05 2309 N Control Method

0_VF

1________

2_Sensorless

Determines the control method of the motor as either a volts to frequency

relationship (Induction Motor) or Sensorless Vector Control (SVC) (Per

manent Magnet).

Motor-06 2310 N Motor Type

0_Induction Motor

1_PM-SPM

2_PM-IPM

Identifies the type of motor being used.

PM-SPM: Surface Permanent Magnet Motor

PM-IPM: Internal Permanent Magnet Motor

Motor-07 2311 N PM Poles

0 to 65535

Identifies the number of poles in Permanent Magnet Motor.

Motor-08 2312 N PM Inertia

0.0 to 6553.5 Kg*m^2

Identifies the inertia in Permanent Magnet Motor. This value is automati

cally calculated.

Motor-09 2313 N PM Rs

0.0 to 65.535 Ohm

Permanent Magnet Motor stator resistance.

Motor-10 2314 N PM Ld

0.0 to 655.35 mH

Permanent Magnet Motor inductance d-axis.

Motor-11

2315 N PM Lq

0.0 to 655.35 mH

Permanent Magnet Motor inductance q-axis.

Motor-12 2316 Y PM PG Angle

0 to 360 degree

Permanent Magnet Motor offset angle.

Motor-13 2317 Y PM Ke Coeff

0 to 65535

Coefficient for optimal PM motor control

Motor-14 2318 Y Rotor Zeroing

0_Disabled

1_1/4 FLA Current

2_Hi Freq Inject

3_Pulse Inject

Permanent Magnet Motor rotor initial angle position detection method.

Recommendation: "2" for IPM; "3" for SPM. If there is a bad effect, then set

as "1".

Содержание Cerus X-Drive





























































































































































Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды

Franklin Electric Cerus X-Drive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды