Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 63

Страница: 63 / 156

OPERATION

Control Options

OPERATION

Control Options

Hand/Auto Controls

The drive can be operated in either

HAND

AUTO

mode as follows:

•

HAND

mode runs the motor based on

Hand Speed Ref [SET–09]

(frequency source) and

Hand

Run Cmd [SET–10]

(command source). Defaults for both settings are Keypad, which runs the

motor at a fixed speed (

Keypad Setpoint

) set on the Home Screen. Both settings can be

reprogrammed for external control. PID control is disabled in Hand mode.

•

AUTO

mode runs the motor based on

AUTO Speed Ref [SET–07]

(frequency source) and

AUTO Run

Cmd [SET–08]

(command source). The speed reference default is set per application. The

run command default is Keypad. Both settings can be reprogrammed as required.

There are several options to consider for operation of the VFD through external HOA controls:

HOA Mode Source [SET–60]:

This setting selects whether Hand/Auto control will come from

the Keypad, a Digital Input, or Communications. When switching modes with the keypad, the
VFD will stop, and will start when the

Start

key is pressed. When switching modes with a DI or

Comm source, the VFD will start based on the presence of a run command.
•

Keypad (Default):

The VFD Keypad HOA buttons, including

Start

and

Stop

, are fully func

tional.

•

Digital Input:

Enables HOA control through an external switch wired to two digital inputs

[MI1 to MI8]. These inputs should be set to

26_Hand

and

27_Auto

through parameters

[IO–21

to 28]

. HOA mode is then determined as follows:

•

RS485 Serial:

Enables HOA control through Modbus communications.

•

Com Card:

Enables HOA control through BACNet communications. The combinations of 0x2002 bit 3

and bit 4 are defined as follows:

Hand Speed Ref [SET–09]:

Source of Speed Reference in Hand mode. When in Hand mode, PID is disabled

and the VFD frequency is based on the following inputs:
•

Keypad (Default):

VFD runs at a fixed frequency set on the Home Screen.

•

RS485 Serial:

Frequency input through Modbus control.

•

AVI1 Analog:

Input from external controller, potentiometer, or other device.

•

ACI Analog:

Input from external controller, potentiometer, or other device.

•

AVI2 Analog:

Input from external controller, potentiometer, or other device.

•

COM Card:

Frequency input through communications protocol.

26_HOA Hand

27_HOA Auto

HOA Mode

Open

OFF

Closed

Open

Hand

Open

Closed

Auto

Closed

OFF

Bit 3

Bit 4

HOA Mode

No change

Hand

Auto

OFF

Содержание Cerus X-Drive





























































































































































Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды

Franklin Electric Cerus X-Drive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды