Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 122

Страница: 122 / 156

PARAMETER REFERENCE TABLES

Parameter Descriptions > I/O Menu

122

Parameter Descriptions > I/O Menu

AR = Adjustable while running.

VFD-47 0303 N VFD Rated Amps (Variable)

Current rating of drive with respect to Light Duty and Normal Duty [VFD-

35] (Read Only).

VFD-48 0304 Y Display Select

0_Freq Command

1_Output Frequency

2_Multi-Fn Display

3_Output Current

Sets the parameter that appears on second line of display.

VFD-49 0305 N Firmware Version (Variable)

VFD software version (Read Only).

VFD-50 0306 Y Disp Filter A

0.001 to 65.535 Sec

Minimizes the current fluctuation displayed by digital keypad.

VFD-51 0307 Y Disp Filter KPD

0.001 to 65.535 Sec

Minimizes the display value fluctuation displayed by digital keypad.

VFD-52 0308 N FW Date

(Variable)

VFD software version date (Read Only).

VFD-53 0309 Y Jog Accel Time

0.0 to (variable) Sec

Acceleration time in jog operation to increase frequency to jog frequency.

VFD-54 0310 Y Jog Decel Time

0.0 to (variable) Sec

Deceleration time in jog operation to decrease frequency to 0Hz.

VFD-55 0311 Y JOG Frequency

0.0 to 600 Hz

Frequency commanded for jog operation.

VFD-56 0312 N Zero-speed Mode 0_Standby

1_Hold by DC Brake

2_Min Frequency

When commanded frequency is less than frequency min:

Standby: VFD stays at 0Hz.

Hold by DC Brake: apply DC Brake by minimium voltage

Frequency Min: VFD runs motor at minimium frequency.

VFD-57 0313 Y Power-on Start

0_Disable

1_Enable

When enabled, the VFD will automatically initiate operation after powered-

on with run command.

CODE Mod

Bus AR Display Name

Range

Description

CODE Mod

Bus AR Display Name

Range

Description

IO-00

0512 N ACI Input Sel

0_0-10V

1_0-20mA

2_4-20mA

3_PTC

4_PT100

Selects the format of the input signal expected at the ACI input terminals

based on the type of control device to be connected—transducer, sensor,

controller, etc. This setting must correspond with ACI micro switch.

IO-01

0513 N ACI Loss Trip

0_Disable

1_Hold Speed

2_Decel Stop

3_Trip Stop

Selects operation when ACI signal is lost.

VFD runs at previous speed (2 sec before signal loss

VFD will restart when signal present

VFD will stay tripped until reset

IO-04

0516 Y ACI Filter T

0 to 20 Sec

ACI time filter for noisy analog signal.

IO-05

0517 N AVI1 Input Sel

0_0-10V

1_0-20mA

2_4-20mA

3_PTC

4_PT100

Selects the format of the input signal expected at the ACI input terminals

based on the type of control device to be connected—transducer, sensor,

controller, etc. This setting must correspond with AVI1 micro switch.

IO-09

0521 Y AVI1 Filter T

0 to 20 Sec

AVI1 time filter for noisy analog signal. The delay time helps buffer interfer

ence that could cause error in the signal input. Longer times improve signal

confirmation, but the response time is delayed.

IO-10

0522 Y AVI2 Filter T

0 to 20 Sec

AVI2 time filter for noisy analog signal. The delay time helps buffer interfer

ence that could cause error in the signal input. Longer times improve signal

confirmation, but the response time is delayed.

IO-11

0523 Y PID Filter Time

0.1 to 300 Sec

PID feedback signal time filter for noisy analog signal. The delay time helps

buffer interference that could cause error in the signal input. Longer times

improve signal confirmation, but the response time is delayed.

IO-12

0524 Y PID Delay Time

0 to 35 Sec

Time delay for frequency command.

IO-13

0525 Y AI Upper Level

-100 to 100%

High level limit of analog input.

IO-14

0526 Y AI Lower Level

-100 to 100%

Low level limit of analog input.

IO-20

0532 Y DI Filter

0 to 30 Sec

Response time of digital input terminals MI1~MI8. The delay time helps buf

fer interference that could cause error in the signal input. Longer times

improve signal confirmation, but the response time is delayed.

Содержание Cerus X-Drive





























































































































































Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды

Franklin Electric Cerus X-Drive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды