Festo CMMP Series Скачать руководство пользователя страница 146

Страница: 146 / 210

7. Device control

146

Festo P.BE-CMMP-CO-SW-EN 0708NH

Bit 12

Dependent on

modes_of_operation

set_point_
acknowledge

In the

Profile Position Mode

This bit is set when the motor controller has

recognised the set bit

new_set_point

in the

controlword

. It is deleted again after the bit

new_set_point

in the

controlword

has been set to

zero. Also see chapter 8.3 on this.

speed_0

In the

Profile Velocity Mode

The bit is set when the currentspeed

(

velocity_actual_value

) of the drive is within the

related tolerance window (

velocity_threshold

homing_attained

In the

Homing Mode

This bit is set when the reference travel has ended

without error.

ip_mode_active

In the

Interpolated Position Mode

This bit shows that interpolation is active and the

interpolation data records have been evaluated. It is
set when requested by the bit

enable_ip_mode

in the

controlword

. See also chapter 8.4.

Bit 13

Dependent on modes_of_operation:

following_error

In the

Profile Position Mode

The bit is set when the current actual position

(

position_actual_value

) differs from the target

position (

position_demand_value

) so much that the

difference lies outside the parameterised tolerance
window (

following_error_window

following_error_

time_out

homing_error

In the

Homing Mode

This bit is set when reference travel is interrupted -

(

Halt

bit), both limit switches are triggered

simultaneously or the limit switch search travel
already performed is greater than the specified
positioning space (

min_position_limit

max_position_ limit

Содержание CMMP Series



















































































































































































































Результаты поиска

Содержание CMMP Series

Отзывы:

Похожие инструкции для CMMP Series

Бренды по названию

Популярные бренды

Festo CMMP Series, Руководство пользователя

Результаты поиска

Содержание CMMP Series

Отзывы:

Похожие инструкции для CMMP Series

Бренды по названию

Популярные бренды