Endress+Hauser PROFI BUS Proline Promag 53 PROFIBUS DP Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 182

background image

Proline Promag 53 PROFIBUS DP/PA

Wiring

Hauser

51

Suitable fieldbus cables from various manufacturers for non-hazardous areas are listed below:
• Siemens: 6XV1 830-5BH10
• Belden: 3076F
• Kerpen: CeL-PE/OSCR/PVC/FRLA FB-02YS(ST)YFL

Maximum overall cable length

The maximum network expansion depends on the type of explosion protection and the cable
specifications. The overall cable length combines the length of the main cable and the length of all
spurs (>1 m).

Note the following points:
• The maximum permissible overall cable length depends on the cable type used:

• If repeaters are used, the maximum permissible cable length is doubled.

A maximum of three repeaters are permitted between user and master.

Maximum spur length

The line between the distribution box and field device is described as a spur.
In the case of non-Ex applications, the max. length of a spur depends on the number of
spurs (>1 m):

Number of field devices

In systems that meet FISCO with EEx ia type of protection, the line length is limited to max. 1000
m. A maximum of 32 users per segment in non-Ex areas or a maximum of 10 users in an Ex-area
(EEx ia IIC) is possible. The actual number of users must be determined during configuration.

Bus termination

The start and end of each fieldbus segment are always to be terminated with a bus terminator. With
various junction boxes (non-Ex), the bus termination can be activated via a switch. If this is not the
case, a separate bus terminator must be installed.

Note the following points:
• In the case of a branched bus segment, the device furthest from the segment coupler represents

the end of the bus.

• If the fieldbus is extended with a repeater then the extension must also be terminated at both

ends.

Further information

General information and further notes regarding the wiring are contained in BA034S/04:
“Guidelines for planning and commissioning, PROFIBUS DP/PA, field communication.”

Type A

1900 m

Type B

1200 m

Number of spurs

1 to 12

13 to 14

15 to 18

19 to 24

25 to 32

Max. length per spur

120 m

90 m

60 m

30 m

1 m

«
...
49
50
51
52
53
...
»

Содержание PROFI BUS Proline Promag 53 PROFIBUS DP























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROFI BUS Proline Promag 53 PROFIBUS DP

Бренд: Wavetek Страницы: 43

Бренд: Parkside Страницы: 94

Disklavier Mark III Series

Бренд: Yamaha Страницы: 39

Бренд: Kawai Страницы: 8

Бренд: Armstrong Monitoring Corporation Страницы: 12

Бренд: Veeco Страницы: 349

Бренд: GrainPro Страницы: 7

Бренд: Caen Страницы: 50

Бренд: Bruker BioSpin Страницы: 76

microCLIMA ULTRA

Бренд: MADDALENA Страницы: 17

Бренд: Kawai Страницы: 2

MarMonix MSL-765

Бренд: Farnell Страницы: 15

Бренд: Shimadzu Страницы: 22

Бренд: IS Technologies Страницы: 21

Бренд: Mityvac Страницы: 24

CHEM2000-UV-VIS

Бренд: Ocean Optics Страницы: 42

MASTERVISION ECO

Бренд: Ega Master Страницы: 48

Бренд: Doepke Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды