Endress+Hauser PROFI BUS Proline Promag 53 PROFIBUS DP Скачать руководство пользователя страница 5

Страница: 5 / 182

Proline Promag 53 PROFIBUS DP/PA

Brief operating instructions

Hauser

Note!

• The display returns to the cell SETUP COMMISSIONING (1002) if you press the ESC key combination during

parameter interrogation. The stored parameters remain valid.

• The “Commissioning” Quick Setup must be carried out before one of the other Quick Setups described in this

Operating Manual is run.

Only units not yet configured in the current Setup are offered for selection in each

cycle. The unit for mass and

volume is derived from the corresponding flow unit.

The “YES” option remains visible until all the units have been configured.
“NO” is the only option displayed when no further units are available.

This prompt only appears if a current output and/or pulse/frequency output is available. Only the outputs not yet
configured in the current Setup are offered for selection in each cycle.

The “YES” option remains visible until all the outputs have been configured.
“NO” is the only option displayed when no further outputs are available.

The “automatic display configuration” option contains the following basic settings/factory settings

YES

Main line = volume flow
Additional line = totalizer 1
Information line = operating/system condition

The existing (selected) settings remain.

➅

The BATCHING QUICK SETUP is only available when the optional software package BATCHING is installed.

➆

The PULSATING FLOW QUICK SETUP is only available if the device has a current output or a pulse/frequency
output.

Содержание PROFI BUS Proline Promag 53 PROFIBUS DP























































































































































































Результаты поиска

Содержание PROFI BUS Proline Promag 53 PROFIBUS DP

Отзывы:

Похожие инструкции для PROFI BUS Proline Promag 53 PROFIBUS DP

Бренды по названию

Популярные бренды

Endress+Hauser PROFI BUS Proline Promag 53 PROFIBUS DP, Руководство по эксплуатации

Результаты поиска

Содержание PROFI BUS Proline Promag 53 PROFIBUS DP

Отзывы:

Похожие инструкции для PROFI BUS Proline Promag 53 PROFIBUS DP

Бренды по названию

Популярные бренды