Endress+Hauser PROFI BUS Proline Promag 53 PROFIBUS DP Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 182

background image

Identification

Proline Promag 53 PROFIBUS DP/PA

14

Hauser

2.2

Certificates and approvals

The devices are designed in accordance with good engineering practice to meet state-of-the-art
safety requirements, have been tested, and left the factory in a condition in which they are safe to
operate. The devices comply with the applicable standards and regulations in accordance with EN
61010 “Protection Measures for Electrical Equipment for Measurement, Control, Regulation and
Laboratory Procedures” and with the EMC requirements of EN 61326/A1.
The measuring system described in this Operating Manual is therefore in conformity with the
statutory requirements of the EC Directives. Hauser confirms successful testing of the
device by affixing to it the CE mark.
The measuring system complies with the EMC requirements of the “Australian Communications
Authority (ACA)”.

The flowmeter has successfully passed all the test procedures carried out and is certified and
registered by the PNO (PROFIBUS User Organization).

The device thus meets all the requirements of the following specifications:
• Certified to PROFIBUS Specification Profile 3.0 version

(Device certification number: provided upon request)

• The measuring device can also be operated with certified devices of other manufacturers

(interoperability).

2.3

Registered trademarks

KALREZ

®

and VITON

®

Registered trademarks of E.I. Du Pont de Nemours & Co., Wilmington, USA

TRI-CLAMP

®

Registered trademark of Ladish & Co., Inc., Kenosha, USA

PROFIBUS

®

Registered trademark of the PROFIBUS User Organization, Karlsruhe, D

HistoROM™, S-DAT

®

, T-DAT™, F-CHIP

®

, ToF Tool - Fieldtool

®

Package, Fieldcheck

®

,

Applicator

®

Registered or registration-pending trademarks of Hauser Flowtec AG, Reinach, CH

«
...
12
13
14
15
16
...
»

Содержание PROFI BUS Proline Promag 53 PROFIBUS DP























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROFI BUS Proline Promag 53 PROFIBUS DP

Бренд: GE Страницы: 8

Moisture Image 1 Series

Бренд: GE Страницы: 110

DigitalFlow GS868

Бренд: GE Страницы: 74

DigitalFlow GS868

Бренд: GE Страницы: 81

Бренд: Baker Hughes Страницы: 59

Бренд: Baker Hughes Страницы: 2

Бренд: Panametrics Страницы: 67

Бренд: Panametrics Страницы: 108

Transport PT878

Бренд: GE Страницы: 97

Бренд: Eagle Eye Страницы: 3

Бренд: VALTRONICS Страницы: 13

Бренд: JIANGSU Страницы: 8

EXTREME DUTY TPMS

Бренд: Valor Страницы: 2

Бренд: Yamaha Страницы: 10

Бренд: Yamaha Страницы: 38

Бренд: Yamaha Страницы: 45

Бренд: Valcom Страницы: 1

Бренд: DGH Страницы: 87

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды