Endress+Hauser PROFI BUS Proline Promag 53 PROFIBUS DP Скачать руководство пользователя страница 154 | Manualshive

Страница: 154 / 182

background image

Troubleshooting

Proline Promag 53 PROFIBUS DP/PA

154

Hauser

Wall-mounted housing

#

Warning!
• Risk of electric shock. Exposed components carry dangerous voltages. Make sure that the power

supply is switched off before you remove the cover of the electronics compartment.

• Risk of damaging electronic components (ESD protection). Static electricity can damage electronic

components or impair their operability. Use a workplace with a grounded working surface
purposely built for electrostatically sensitive devices!

• If you cannot guarantee that the dielectric strength of the device is maintained in the following

steps, then an appropriate inspection must be carried out in accordance with the manufacturer’s
specifications.

• When connecting Ex-certified devices, see the notes and diagrams in the Ex-specific supplement

to this Operating Manual.

"

Caution!
Use only original Hauser parts.

Installing and removing the circuit boards

Fig. 72: Wall-mount housing

1.

Remove the screws and open the hinged cover (1) of the housing.

2.

Remove the screws securing the electronics module (2). Then push up electronics module and
pull it as far as possible out of the wall-mount housing.

3.

Disconnect the following cable plugs from amplifier board (7):
– Electrode signal cable plug (7.1) including S-DAT (7.3)
– Plug of coil current cable (7.2):

Loosen the plug locking and gently disconnect the plug from the board, i.e. without moving
it back and forward.

– Ribbon cable plug (3) of the display module

4.

Remove the cover (4) from the electronics compartment by loosening the screws.

5.

Remove the boards (6, 7, 8):
(5) Insert a thin pin into the hole provided for the purpose and pull the board clear of its holder.

6.

Removing sub-modules (8.2, only for measuring devices with convertible I/O board):
No tools are required for removing the submodules (inputs/outputs) from the I/O board.
Installation is also a no-tools operation.

"

Caution!

Only certain combinations of submodules on the
I/O board are permissible.

The individual slots are marked and correspond to certain terminals in the connection
compartment of the transmitter:

“INPUT / OUTPUT 3” slot = terminals 22/23
“INPUT / OUTPUT 4” slot = terminals 20/21

7.

Installation is the reverse of the removal procedure.

«
...
152
153
154
155
156
...
»

Содержание PROFI BUS Proline Promag 53 PROFIBUS DP























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROFI BUS Proline Promag 53 PROFIBUS DP

Бренд: Yamaha Страницы: 2

Бренд: IEI Technology Страницы: 85

Бренд: Raytech Страницы: 18

Бренд: Zeversolar Страницы: 35

Бренд: Zenner Страницы: 52

Бренд: Teradek Страницы: 16

Бренд: Johnson & Associates Страницы: 33

Бренд: PCE Health and Fitness Страницы: 11

SensoControl Serviceman SCM-150 Series

Бренд: Parker Страницы: 39

Бренд: OHAUS Страницы: 6

Бренд: Endress+Hauser Страницы: 24

Бренд: sebaKMT Страницы: 131

Бренд: Harken Страницы: 2

Бренд: Huvitz Страницы: 58

Бренд: Alma Страницы: 69

WTW SensoLyt 900

Бренд: Xylem Страницы: 12

Бренд: GasQuip Страницы: 8

Бренд: TEA Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды