Endress+Hauser PROFI BUS Proline Promag 53 PROFIBUS DP Скачать руководство пользователя страница 168 | Manualshive

Страница: 168 / 182

background image

Technical data

Proline Promag 53 PROFIBUS DP/PA

168

Hauser

The permitted fluid temperature is dependent on the material of the seal:
• EPDM: –20 to +130 °C
• Silicone: –20 to +150 °C
• Viton: –20 to +150 °C
• Kalrez: –20 to +150 °C

Conductivity

Minimum conductivity
•

≥

5 µS/cm for liquids generally

•

≥

20 µS/cm for demineralized water

!

Note!
Note that, in the case of the remote version, the requisite minimum conductivity is also influenced
by the length of the connecting cable.

Fluid pressure range (nominal
pressure)

Promag W

• EN 1092-1 (DIN 2501):

PN 6 (DN 1200 to 2000), PN 10 (DN 200 to 2000), PN 16 (DN 65 to 2000), PN 25 (DN 200
to 1000), PN 40 (DN 25 to 150)

• ANSI B 16.5:

Class 150 (DN 1" to 24"), Class 300 (DN 1" to 6")

• AWWA:

Class D (DN 28" to 78")

• JIS B2238:

10 K (DN 50 to 300), 20 K (DN 25 to 300)

• AS 2129:

Table E (DN 80, 100, 150 to 400, 500, 600)

• AS 4087:

Cl. 14 (DN 80, 100, 150 to 400, 500, 600)

Promag P

• EN 1092-1 (DIN 2501):

PN 10 (DN 200 to 600), PN 16 (DN 65 to 600), PN 25 (DN 200 to 600), PN 40 (DN 15 to 150)

• ANSI B 16.5:

Class 150 (DN

1

/

2

" to 24"), Class 300 (DN

1

/

2

" to 6")

• JIS B2238:

10 K (DN 50 to 300), 20 K (DN 15 to 300)

• AS 2129:

Table E (DN 25, 50)

• AS 4087:

Cl. 14 (DN 50)

Promag H

The permissible nominal pressure depends on the process connection and the seal:
• 40 bar: flange, weld nipple (with O-ring seal)
• 16 bar: all other process connections

Resistance to partial vacuum
(measuring tube lining)

Promag W

Nominal diameter

Measuring tube

lining

Resistance of measuring tube lining to partial vacuum

Limit values for abs. pressure [mbar] at various

fluid temperatures

[mm]

[inch]

25 °C

50 °C

80° C

100 °C

130 °C

150 °C

180 °C

25 to 1000

1 to 40"

Polyurethane

0

0

-

-

-

-

-

65 to 2000

3 to 78"

Hard rubber

0

0

0

-

-

-

-

«
...
166
167
168
169
170
...
»

Содержание PROFI BUS Proline Promag 53 PROFIBUS DP























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROFI BUS Proline Promag 53 PROFIBUS DP

Бренд: Kawai Страницы: 70

Бренд: ABQ Industrial Страницы: 15

Бренд: ABQINDUSTRIAL Страницы: 3

Бренд: Omano Страницы: 14

Comark Diligence 600

Бренд: Fluke Страницы: 61

SF6 Portable Monitor

Бренд: Bacharach Страницы: 2

Бренд: Agilent Technologies Страницы: 198

Бренд: RS PRO Страницы: 41

Бренд: Magnusson Страницы: 96

Бренд: Fluke Страницы: 97

Бренд: ATIM Страницы: 32

Бренд: Kobold Страницы: 27

Бренд: LaserLine Страницы: 15

Бренд: PRECISION DIGITAL Страницы: 52

Бренд: OBDPROG Страницы: 15

Бренд: Stageline Страницы: 30

N4906B Serial BERT

Бренд: Agilent Technologies Страницы: 12

Бренд: FCI Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды