Endress+Hauser PROFI BUS Proline Promag 53 PROFIBUS DP Скачать руководство пользователя страница 175 | Manualshive

Страница: 175 / 182

background image

Proline Promag 53 PROFIBUS DP/PA

Technical data

Hauser

175

10.1.12 Certificates and approvals

CE mark

The measuring system is in conformity with the statutory requirements of the EC Directives.
Hauser confirms successful testing of the device by affixing to it the CE mark.

C-Tick symbol

The measuring system complies with the EMC requirements of the “Australian Communications
Authority (ACA)”.

Ex approval

Information about currently available Ex versions (ATEX, FM, CSA etc.) can be supplied by your
E+H Sales Center on request. All information relevant to explosion protection is available in
separate Ex documents that you can order as necessary.

Compatibility with foodstuffs

Promag W

No applicable approvals or certification

Promag P

No applicable approvals or certification

Promag H

• 3A authorization and EHEDG-tested
• Seals

→

in conformity with FDA (except Kalrez seals)

PROFIBUS DP/PA
certification

The flowmeter has successfully passed all the test procedures carried out and is certified and
registered by the PNO (PROFIBUS User Organization). The device thus meets all the requirements
of the following specifications:

• Certified in accordance with PROFIBUS Profile Version 3.0 (device certification number: available

on request)

• The measuring device can also be operated with certified devices of other manufacturers

(interoperability).

Pressure device approval

Measuring devices with a nominal diameter smaller than or equal to DN 25 correspond to Article
3(3) of the EC Directive 97/23/EC (Pressure Equipment Directive) and have been designed and
manufactured according to good engineering practice. For larger nominal diameters, optional
approvals according to Cat. II/III are available when required (depends on fluid and process
pressure).

Other standards and
guidelines

• EN 60529

Degrees of protection by housing (IP code)

• EN 61010

Protection Measures for Electrical Equipment for Measurement, Control, Regulation and
Laboratory Procedures.

• EN 61326/A1 (IEC 1326)

“Emission in accordance with requirements for Class A”.
Electromagnetic compatibility (EMC-requirements).

• NAMUR NE 21

Electromagnetic compatibility (EMC) of industrial process and laboratory control equipment.

• NAMUR NE 43

Standardization of the signal level for the breakdown information of digital transmitters with
analog output signal.

• NAMUR NE 53

Software of field devices and signal-processing devices with digital electronics.

«
...
173
174
175
176
177
...
»

Содержание PROFI BUS Proline Promag 53 PROFIBUS DP























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROFI BUS Proline Promag 53 PROFIBUS DP

Бренд: M3S Страницы: 40

Бренд: ICS Schneider Messtechnik Страницы: 40

Бренд: YOSensi Страницы: 3

Бренд: A&D Страницы: 68

Бренд: Trebs Страницы: 44

Greenlee CLM-1000

Бренд: Textron Страницы: 36

Бренд: Rhosonics Страницы: 65

Бренд: Lasertec Страницы: 28

Бренд: Power Measurement Страницы: 20

Бренд: Lutron Electronics Страницы: 43

Бренд: Dakota Digital Страницы: 38

Бренд: Swema Страницы: 4

Бренд: Hanna Instruments Страницы: 28

Бренд: Magnescale Страницы: 36

Бренд: Vanguard Instruments Страницы: 85

Бренд: Veeder-Root Страницы: 12

Бренд: Quadelectra Audioworx Страницы: 12

Бренд: horiba Страницы: 103

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды