Endress+Hauser PROFI BUS Proline Promag 53 PROFIBUS DP Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 182

background image

Commissioning

Proline Promag 53 PROFIBUS DP/PA

108

Hauser

6.5.2

Selection of the GSD file in the measuring device

Depending on which GSD file is used in the PROFIBUS master system, the corresponding GSD file
has to be configured in the device by means of the SELECTION GSD function.

BASIC FUNCTION (G)

→

PROFIBUS DP/PA (GBA/GCA)

→

OPERATION (614)

→

SELECTION

GSD (6140)

Example

Before configuration takes place, a decision should be made as to which GSD file should be used to
configure the measuring device in the PROFIBUS master system. Below, the use of the
manufacturer-specific GSD file (complete device functionality) is shown using

PROFIBUS PA

as an

example:

Select the manufacturer-specific GSD file in the measuring device by means of the SELECTION
GSD function.

BASIC FUNCTION (G)

→

PROFIBUS PA (GCA)

→

OPERATION (614)

→

SELECTION GSD

(6140)

→

Selection: MANUFACT. SPEC. (factory setting)

1.

Before configuring the network, load the corresponding GSD file into the configuration
system/master system.

!

Note!

When installing the GSD file, always first use the GSD file with the extended format
(EH3x1527.gsd). However, if the installation or the configuration of the device fails with this
format, then use the standard GSD (EH3_1527.gsd).

Example for the configuration software Siemens STEP 7 of the Siemens PLC family S7-300/
400:
Use the GSD file with the extended format (EH3x1527.gsd). Copy the file to the subdirectory
“...siemensstep7s7datagsd”. The GSD files also include bitmap files. These bitmap files are
used to display the measuring points in image form. The bitmap files must be saved to the
directory “...siemensstep7s7datansbmp”.

If you are using configuration software other than that referred to above, ask your PROFIBUS
master system manufacturer which directory you should use.

2.

The measuring device is a modular PROFIBUS slave, i.e. the desired module configuration
(input and output data) must be performed in the next step. This can be done directly by means
of the configuration software. A detailed description of the modules supported by the
measuring device as follows:
PROFIBUS DP

PROFIBUS PA

Promag 53 GSD file:

→

Select: MANUFACT. SPEC. (factory setting)

Profile GSD file

→

Select: PROFILE-GSD

Promag 33 GSD file:

→

Select: MANUFACT V2.0

«
...
106
107
108
109
110
...
»

Содержание PROFI BUS Proline Promag 53 PROFIBUS DP























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROFI BUS Proline Promag 53 PROFIBUS DP

Бренд: Bacharach Страницы: 60

Бренд: Bacharach Страницы: 4

Бренд: Bacharach Страницы: 17

Бренд: Hach Страницы: 28

Бренд: Nellcor Страницы: 104

CP-4900 Micro-GC

Бренд: Varian Страницы: 7

Бренд: Vapotherm Страницы: 2

Бренд: Keithley Страницы: 31

Бренд: Keithley Страницы: 63

Бренд: Keithley Страницы: 18

Бренд: Keithley Страницы: 73

Бренд: Keysight Страницы: 92

Frontline 802.11

Бренд: Teledyne Lecroy Страницы: 223

Бренд: Omicron Страницы: 76

Бренд: Galileo Страницы: 30

Бренд: R&S Страницы: 130

Бренд: Kinesys Страницы: 10

Бренд: REED Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды