Endress+Hauser PROFI BUS Proline Promag 53 PROFIBUS DP Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 182

background image

Proline Promag 53 PROFIBUS DP/PA

Installation

Hauser

41

3.3.3

Installing the Promag H sensor

The Promag H is supplied to order, with or without pre-installed process connections. Pre-installed
process connections are secured to the sensor with 4 hex-head screws.

"

Caution!
The sensor might require support or additional attachments, depending on the application and the
length of the piping run. When plastic process connections are used, the sensor must be additionally
supported mechanically. A wall-mounting kit can be ordered separately from Hauser as an
accessory.

a0004301

Fig. 23:

Promag H process connections (DN 2 to 25, DN 40 to 100)

A = DN 2 to 25/process connections with O-ring
Weld nipples (DIN EN ISO 1127, ODT/SMS), flange (EN (DIN), ANSI, JIS), flange PVDF (EN (DIN), ANSI, JIS), external
and internal pipe threads (ISO/DIN), hose connection, PVC adhesive coupling

B = DN 2 to 25/process connections with aseptic molded seal
Weld nipples (DIN 11850, ODT/SMS), Clamp (ISO 2852, DIN 32676, L14 AM7),
threaded connection (DIN 11851, DIN 11864-1, SMS 1145), flange DIN 11864-2

C = DN 40 to 100/process connections with aseptic molded seal
Weld nipples (DIN 11850, ODT/SMS), Clamp (ISO 2852, DIN 32676, L14 AM7),
threaded connection (DIN 11851, DIN 11864-1, ISO 2853, SMS 1145), flange DIN 11864-2

Seals

When installing the process connections, make sure that the seals are clean and correctly centered.

"

Caution!
• With metallic process connections, you must fully tighten the screws. The process connection

forms a metallic connection with the sensor, which ensures a defined compression of the seal.

• With plastic process connections, note the max. torques for lubricated threads (7 Nm). With

plastic flanges, always use seals between connection and counter flange.

• The seals must be replaced periodically, depending on the application, particularly in the case of

molded seals (aseptic version)! The period between changes depends on the frequency of cleaning
cycles, the cleaning temperature and the fluid temperature. Replacement seals can be ordered as
accessories.

DN 2...25

A

B

C

DN 40...100

«
...
39
40
41
42
43
...
»

Содержание PROFI BUS Proline Promag 53 PROFIBUS DP























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROFI BUS Proline Promag 53 PROFIBUS DP

Бренд: rainforest Страницы: 2

Бренд: ParTech Страницы: 14

Бренд: Valor Страницы: 13

Бренд: Campbell Страницы: 31

Бренд: ICS Страницы: 2

Бренд: CAISSON Страницы: 5

Бренд: YOKOGAWA Страницы: 16

Бренд: Keller Страницы: 4

Бренд: Kawai Страницы: 72

Бренд: Sensitech Страницы: 2

Commissioner dali

Бренд: Artistic License Страницы: 26

Бренд: Vaisala Страницы: 11

Бренд: WAGNER Страницы: 4

Бренд: PKP Страницы: 7

ProScale 950 Series

Бренд: Accurate Technology Страницы: 16

Бренд: Omega Страницы: 14

Бренд: AlazarTech Страницы: 60

Бренд: Kobold Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды