Endress+Hauser PROFI BUS Proline Promag 53 PROFIBUS DP Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 182

background image

Proline Promag 53 PROFIBUS DP/PA

Commissioning

Hauser

113

Assignment of the measured variables to the TOTAL module

The TOTAL module can transmit different totalizer variables to the PROFIBUS master (Class 1).
The measured variables are assigned to the totalizer function blocks 1 to 3 by means of the local
display or with the aid of an operating program (e.g. FieldCare) in the CHANNEL function:

BASIC FUNCTION (G)

→

PROFIBUS DP (GBA)

→

TOTALIZER (613)

→

SELECT TOTALIZER (6130): Selection of a totalizer

→

CHANNEL (6133): Selection of measured variable

Possible settings

Factory setting

SETTOT_TOTAL module

The module combination SETTOT_TOTAL (slots 2 to 4) consists of the functions SETTOT and
TOTAL.
With this module combination:
• The totalizer can be controlled via the automation system (SETTOT).
• The totalizer value, is transmitted, including the status (TOTAL)

SETTOT function

In the SETTOT function, the totalizer can be controlled via control variables.
The following control variables are supported:
• 0 = Totalize (factory setting)
• 1 = Reset totalizer (the totalizer value is reset to 0)
• 2 = Accept totalizer preset

!

Note!
After the totalizer value has been reset to 0 or set to the preset value, the totalizing continues
automatically. The control variable does not have to be changed to 0 again to restart totalizing.
Stopping totalizing is controlled in the SETTOT_MODETOT_TOTAL module via the MODETOT
function.

TOTAL function

For a description of the TOTAL function, refer to TOTAL module

Totalizer value/measured variable

ID for CHANNEL function

VOLUME FLOW

273

MASS FLOW

277

OFF

0

Module

Totalizer

function block

Totalizer value/

Measured variable

Unit

ID for CHANNEL

function

TOTAL (slot 2)

1

VOLUME FLOW

m

3

273

TOTAL (slot 3)

2

VOLUME FLOW

m

3

273

TOTAL (slot 4)

3

VOLUME FLOW

m

3

273

«
...
111
112
113
114
115
...
»

Содержание PROFI BUS Proline Promag 53 PROFIBUS DP























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROFI BUS Proline Promag 53 PROFIBUS DP

Бренд: Kawai Страницы: 2

Бренд: Datron Страницы: 197

AccuPoint 2 ATP

Бренд: Neogen Corporation Страницы: 16

Бренд: Vigor Equipment Страницы: 12

Бренд: Trotec Страницы: 14

Бренд: PASCO Страницы: 2

Analite NEP-5000

Бренд: Observator Instruments Страницы: 103

Friendly Digital Piano Forte PV35

Бренд: Kawai Страницы: 102

Бренд: Integra Страницы: 32

SensoControl ServiceJunior Series

Бренд: Parker Страницы: 148

Бренд: Stahl Страницы: 47

Бренд: Bante Instruments Страницы: 7

Бренд: dallmeier Страницы: 93

Бренд: Crowcon Страницы: 37

Бренд: Roland Страницы: 23

Бренд: Landtek Страницы: 3

Бренд: LaMotte Страницы: 32

Бренд: wtw Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды