Endress+Hauser PROFI BUS Proline Promag 53 PROFIBUS DP Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 182

background image

Proline Promag 53 PROFIBUS DP/PA

Installation

Hauser

43

Welding the transmitter into the piping (weld nipples)

"

Caution!
Risk of destroying the measuring electronics. Make sure that the welding machine is

not

grounded

via the sensor or the transmitter.

1.

Tack-weld the Promag H sensor into the pipe. A suitable welding jig can be ordered separately
from Hauser as an accessory.

2.

Loosen the screws on the process connection flange and remove the sensor including the seal
from the piping.

3.

Weld the process connection into the pipe.

4.

Reinstall the sensor in the pipe. Make sure that everything is clean and that the seal is correctly
seated.

!

Note!
• If thin-walled foodstuffs pipes are not welded correctly, the heat could damage the installed seal.

It is therefore advisable to remove the sensor and the seal prior to welding.

• The pipe has to be spread approximately 8 mm to permit disassembly.

Cleaning with pigs

When using pigs for cleaning, it is essential to take the inside diameters of the measuring tube and
process connection into account. All the dimensions and lengths of the sensor and transmitter are
provided in the separate documentation “Technical information”.

«
...
41
42
43
44
45
...
»

Содержание PROFI BUS Proline Promag 53 PROFIBUS DP























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROFI BUS Proline Promag 53 PROFIBUS DP

Бренд: Parr Instrument Company Страницы: 130

Бренд: jenway Страницы: 17

Бренд: Camille Bauer Страницы: 11

Бренд: Camille Bauer Страницы: 83

Бренд: Camille Bauer Страницы: 62

Бренд: YOKOGAWA Страницы: 2

ADMAG TI Series

Бренд: YOKOGAWA Страницы: 8

Бренд: EPE Conseil Страницы: 3

Бренд: Primes Страницы: 48

Бренд: MULTISPAN Страницы: 4

Бренд: LaserLiner Страницы: 84

Бренд: Velleman Страницы: 13

Бренд: A&D Страницы: 2

Бренд: Bulteh 2000 Страницы: 80

dry-cal dc-lite

Бренд: BIOS Страницы: 10

Бренд: Ziton Страницы: 2

Бренд: bihl+Wiedemann Страницы: 16

touchMATRIX WDG 053XIOM

Бренд: Wachendorff Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды