Endress+Hauser PROFI BUS Proline Promag 53 PROFIBUS DP Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 182

background image

Proline Promag 53 PROFIBUS DP/PA

Commissioning

Hauser

109

6.5.3

Compatibility to the previous model Promag 33
(Profile Version 2.0)

Promag 33 with Profile Version 2.0 is the precursor to Promag 53. If Promag 33 is already being
operated in the system and if the measuring device has to be replaced, Promag 53 can be used as a
replacement device without having to reconfigure the PROFIBUS network.
In the event of a device being replaced, Promag 53 completely supports the compatibility of the
cyclic data with the previous Promag 33 model.

The measuring devices can be exchanged as follows:

Promag 53 is accepted as the replacement device if the MANUFACT V2.0 option is activated in the
SELECTION GSD (6140) function.
The measuring device automatically detects that a Promag 33 device was configured in the
automation system and makes both suitable input and output data and measured value status
information available even though the devices differ in name and ID number. You do not have to
adjust the configuration of the PROFIBUS network in the automation system.

Procedure after replacing the measuring devices:

1.

Set the same (old) device address

→

FIELDBUS ADDRESS (6101) function

2.

In the SELECTION GSD (6140) function

→

Select MANUFACT V2.0

3.

Restart the measuring device

→

SYSTEM RESET (8046) function

!

Note!
If necessary, the following settings have to be configured via an operating program:
• Configuration of the application-specific parameters
• Configuration of the system units for the measured values and totalizers.

6.5.4

Maximum number of writes

If a nonvolatile device parameter is modified via the cyclic or acyclic data transmission, this change
is saved in the EEPROM of the measuring device.
The number of writes to the EEPROM is technically restricted to a maximum of 1 million. Attention
must be paid to this limit since, if exceeded, it results in data loss and measuring device failure. For
this reason, avoid constantly writing nonvolatile device parameters via the PROFIBUS!

Existing device:

GSD file used:

→

To be replaced with:

Promag 33 PROFIBUS DP
(ID No. 0x1511)

Extended Format:
or
Standard Format:

EH3x1511.gsd

EH3_1511.gsd

→

Promag 53 PROFIBUS DP

Promag 33 PROFIBUS PA
(ID No. 0x1505)

Extended Format:
or
Standard Format:

EH3x1505.gsd

EH3_1505.gsd

→

Promag 53 PROFIBUS PA

«
...
107
108
109
110
111
...
»

Содержание PROFI BUS Proline Promag 53 PROFIBUS DP























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROFI BUS Proline Promag 53 PROFIBUS DP

Бренд: UEi Страницы: 4

Бренд: Yamaha Страницы: 8

Бренд: Oldham Страницы: 22

Бренд: Unipulse Страницы: 129

Бренд: IDEAL Страницы: 11

Бренд: IDEAL Страницы: 16

LaserRange-Master T4 Pro

Бренд: LaserLiner Страницы: 68

DC1500 CHLORINE

Бренд: LaMotte Страницы: 60

Бренд: VeEX Страницы: 842

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 16

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 7

Бренд: Yamaha Страницы: 60

GranTouch Digital Grand Piano

Бренд: Yamaha Страницы: 19

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды