Doran 4100L Скачать руководство пользователя страница 81

Страница: 81 / 95

Error code:

"Er SP.o"

Selected span calibration value (displayed weight) is

over full scale capacity.

Cause:

Improper setting of calibration span value or test load too heavy.

Remedy:

Recheck test weight value and reset span.

Error Code:

"Er SP.u"

Selected span calibration value (displayed weight) is

less than 20% of full scale capacity.

Cause:

Improper setting of calibration span value or test load too light.

Remedy:

Recheck test weight value and reset span.

Error Code:

"Er dn"

Attempting to adjust calibration span value down with

less than 20% of full scale capacity on the platform.

Cause:

Test load too light.

Remedy:

Use heavier test weight.

Error Code:

"Er SP.-"

Span setting negative.

Cause:

Improper calibration span setting.

Remedy:

Reset span to positive.

Error Code:

"Er or.0"

Zero Over Error - Legal For Trade scales.

Cause:

Attempting to zero too large of a weight (1.9% or 4.0% of scale
capacity), lost calibration, or load cell zero shift (load cell may be
damaged).

Remedy:

Remove the load from the platform and reset the scale, or recalibrate,
or replace load cell.

Error Code:

"Er ur.0"

Zero Under Error - Legal For Trade scales.

Cause:

Lost calibration, or load cell zero shift (load cell may be damaged).

Remedy:

Recalibrate scale, or replace load cell.

Section 10 Error Codes

Содержание 4100L
































































































Результаты поиска

Содержание 4100L

Отзывы:

Doran 4100L, Инструкция по эксплуатации, Страница: 81 / 95

Результаты поиска

Содержание 4100L

Отзывы: