Doran 4100L Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 95

Doran 4100L Скачать руководство пользователя страница 10

UNPACKING

Before proceeding to unpack your Model 4200, please note that although it is a highly
durable industrial scale indicator, it is also a sensitive weighing instrument. Normal care
should be taken when handling and using the indicator. Improper handling or abuse could
be damaging and result in costly repairs that may not be covered by the warranty. Please
observe the following precautions to insure years of trouble-free service from your Model
4200.

* DO NOT drop the scale indicator or platform.

* DO NOT immerse the scale indicator or platform.

* DO NOT drop objects on the platform.

* DO NOT pick up the scale platform by the "spider".

Carefully remove the Model 4200 from the shipping carton. Be sure to retain the shipping
carton and all packaging material in case reshipment is required.

INSTALLATION

4200 Tower: Models with 10" x 10", 12" x 12", and 12" x 16" platforms are shipped in

one piece (fully assembled). When unpacking models with 18" x 18", 18" x
24", and 24" x 24" platforms, note that the scale is shipped with the indicator
column detached from the weighing platform. To attach the indicator column
to the platform, first locate a suitable area at the edge of a table or bench that
is taller than the indicator column assembly. Lift the indicator off the platform
and set it aside. Note that the indicator and platform are connected by a 5'
cable; be careful not to pull on this cable.

Remove the platter from the weighing platform and set it aside. Invert the
platform and set it such that the side holding the four indicator column
mounting bolts is at the edge of the table. Remove the four mounting bolts
from the bottom of the mounting holes. Reinstall and tighten the four
mounting bolts. The indicator column mounts to the support plate with 4
1/4"-20 x 1/2" hex head screws. Lift the indicator column and point it down
towards the floor with the display facing the platform. Align the 4 mounting
holes in the base of the column with the corresponding 4 holes in the support
plate. Install and tighten the 4 hex head screws.

Section 1 Unpacking and Installation

2

«
...
8
9
10
11
12
...
»

Содержание 4100L
































































































Отзывы:

Нет отзывов