433
Other Convenient Functions
e
The charge is automatically reset even during packet
communication.
e
If it becomes time to reset charge automatically
during a call, Auto reset is performed after the call
ends.
e
If it becomes time to reset charge automatically while
a FOMA terminal is turned off, turn on the terminal
again and enter the PIN2 code to reset the charge.
e
Setting Auto reset total cost to "ON" and changing the
month in "Set time" reset the total call charges
automatically.
e
When Auto reset total cost is set to "ON", the PIN2
code entry screen appears when a FOMA terminal is
turned on.
e
Auto reset total cost is set to "OFF" if:
a
You turn on a FOMA terminal without the FOMA
card (UIM) inserted.
a
You press
t
on the PIN2 code entry screen
displayed when a FOMA terminal is turned on.
a
The PIN2 code is locked.
→
p.159
a
The FOMA card (UIM) is failed.
<Notice designate calls>
Setting the Upper Limit of
Charge to Show the Alarm
The standby screen or alarm notifies you when
the accumulated charge indicated in "Call data"
exceeds the specified cost limit.
c
The alarm is given only once when the
accumulated charge exceeds the limit set in
advance.
c
Exceeding the limit does not prevent you from
making calls.
a
i
X
"SETTINGS"
X
"Call time/
Charge"
X
"Notice designate calls"
X
Enter
your security code
X
Set the
respective parameters
X
o
(Finish)
e
The alarm volume applied while in original manner mode is
the same as that specified in "Phone vol. " under "Original".
e
The charges for PushTalk calls, i-mode and packet
communication and Chaku-moji transmission are not
supported by this function. To check i-mode
communication charges, see the "Mobile Phone User's
Guide [i-mode]" you received at the time of contract.
d
Alarm actions
When the accumulated charge exceeds the cost
limit after a call, you are notified as follows:
■
When Notify cost limit is set
to "ON" and Alarm tone is
set to other than "OFF"
When the accumulated call
charge exceeds the preset cost
limit, the alarm sounds for about
five minutes after three seconds
after calling with the screen which notifies that. To
stop the alarm, press any key. After the alarm,
pressing
t
or
y
shows the "
" (Notice
designate calls) desktop icon on the standby screen.
■
When Notify cost limit is set to "ON" and
Alarm tone is set to "OFF"
When the accumulated charge exceeds the preset
cost limit, the "
" (Notice designate calls) desktop
icon appears on the standby screen.
d
Checking the details of
"
"(Notice designate calls)
Selecting the "
" (Notice designate calls)
desktop icon on the standby screen shows the
details of Notice designate calls.
a
On the standby
screen
X
d
X
"
"
X
Enter your security
code
The alarm information on
"Notice designate calls" is
shown.
b
Check the details
X
d
The standby screen reappears and the "
"
(Notice designate calls) desktop icon disappears.
NOTE
Default setting
Cost limit setting: Not set
Notify cost limit: OFF
Cost limit
setting
Sets the cost limit between 10 and
100,000 by 10.
Notify setting
• Notify cost
limit
Specifies whether to give an alarm
when the cost limit is exceeded.
Setting "OFF" does not given an
alarm.
Setting "ON" gives an alarm following the
settings of "Alarm tone" and "Volume".
• Alarm tone
Selects an alarm tone. If you have
created folders, they appear next to
the "Pre-installed" item. "Alarm Tone"
can be selected from the
"Pre-installed" folder.
• Inbox
Selects a melody downloaded from
an i-mode site or website as an alarm
tone.
• Pre-install
ed
Selects an alarm tone from the
pre-installed ring tones and
melodies.
• Voice
announce
Selects "Voice announce 1" or "Voice
announce 2" for an alarm tone.
"Recording and Playing Alarm Tones
and On Hold Tones"
→
p.431
• OFF
Does not sound an alarm.
• Volume
Use
c
to set the alarm tone volume.
NOTE
Ｓｅｔ−ｕｐ ｃｏｓｔ ｌｉｍｉｔ
ｉｓ ｅｘｃｅｅｄｅｄ
Ｃｏｓｔ ｌｉｍｉｔ
Ｄａｔｅ
９／ ４ １１：５０
￥３０００
Ｎｏｔｉｃｅ ｄｅｓｉｇｎａｔｅ ｃａｌｌｓ
Continued on next page
