10
Check that all the components are correct, then press the POWER operation
switch on the main unit to turn on the power.
Press the SYSTEM button to enter the setting.
Press the SELECT or
(down) button to switch to the speaker configuration
set up.
NOTE:
Press the SYSTEM button again to finish system set up. System set up can be finished at any time. The changes
to the settings made up to that point are entered.
1
2
3
*SYSTEM SET UP
Before setting up the system
NOTE:
Please make sure the “AUDIO” position of the slide switch on the
remote control unit.
(Main unit)
Use the
(left) and
(right) buttons to select your center speaker type.
Press the SELECT or
(down) button to switch to the surround speaker setting.
2 CENTER SMALL
LARGE
SMALL
NONE
NOTE:
• When “Small” has been selected for the front speakers, “Large” cannot be selected for the center speaker.
Use the
(left) and
(right) buttons to select your surround speaker type.
3
2
Press the SELECT or
(down) button to switch to the subwoofer setting.
3 SURR. SMALL
LARGE
SMALL
NONE
NOTE:
• When “Small” has been selected for the front speakers, “Large” cannot be selected for the surround speakers.
Setting the speaker configuration
Use the
(left) and
(right) buttons to select your front speaker type.
Press the SELECT or
(down) button to switch to the center speaker setting.
1 FRONT LARGE
LARGE
SMALL
(right) button
(left) button
1
(right) button
(left) button
(right) button
(left) button
(Initial)
(Initial)
(Initial)
ENGLISH
Use the
(left) and
(right) buttons to select your subwoofer setting.
4
Press the SELECT or
(down) button to enter the settings and switch to the
SUBWOOFER MODE setting.
4 S.WOOFER YES
YES
NO
•
Parameters
Large…… Select this when using speakers that can fully reproduce low sounds of below 80 Hz.
Small…… Select this when using speakers that cannot reproduce low sounds of below 80 Hz with sufficient
volume. When this setting is selected, low frequencies of below 80 Hz are assigned to the subwoofer.
None…… Select this when no speakers are installed.
Yes/No…. Select “Yes” when a subwoofer is installed, “No” when it’s not installed.
NOTE:
Select “Large” or “Small” not according to the physical size of the speaker, but according to the bass reproduction
capacity at 80 Hz. If you cannot determine the best setting, try comparing the sound when set to “Small” and
when set to “Large”, at a level that will not damage the speakers.
Caution:
In case the subwoofer is not used, be sure to set “Subwoofer = No”, or the bass sound of front channel is divided
to subwoofer channel and not reproduced in some mode.
(right) button
(left) button
(Initial)
Setting the SUBWOOFER MODE
Use the
(left) and
(right) buttons to select the Subwoofer mode.
Press the SELECT or
(down) button to enter the setting and switch to the
DELAY TIME setting.
5 SW MODE NORM
NORM
+MAIN
(right) button
(left) button
1
NOTES:
— Assignment of low frequency signal range —
• The only signals produced from the subwoofer channel are LFE signals (during playback of Dolby Digital or
DTS signals) and the low frequency signal range of channels set to “SMALL” in the setup menu. The low
frequency signal range of channels set to “LARGE” are produced from those channels.
— Subwoofer mode —
• The subwoofer mode setting is only valid when “LARGE” is set for the front speakers and “YES” is set for
the subwoofer in the “Speaker Configuration” settings (see page 10).
If “SMALL” is set for the front speakers or “NO” is set for the subwoofer, the subwoofer mode setting does
not affect playback of low frequency signal range.
• When the “+MAIN” playback mode is selected, the low frequency signal range of channels set to “LARGE”
are produced simultaneously from those channels and the subwoofer channel.
In this playback mode, the low frequency range expand more uniformly through the room, but depending on
the size and shape of the room, interference may result in a decrease of the actual volume of the low frequency
range.
• When the “NORM” playback mode is selected, the low frequency signal range of channels set to “LARGE”
are only produced from those channels. In this playback mode there tends to be little interference of the low
frequency range in the room.
• Try playing the music or movie source and select the playback mode providing the stronger low frequency
range sound.
(Initial)
