306
| Third-Party Security Integration for AWMS
Dell PowerConnect W AirWave 7.1
| User Guide
AWMS version 1.5 or higher
Completion of the AMP Setup > Radius Accounting page configurations, as described in
“Integrating a
RADIUS Accounting Server” on page
65
.
ReefEdge Configuration
Perform these steps to configure a ReefEdge security scheme:
1. Login into the ReefEdge ConnectServer via HTTP with the proper user credentials.
2. Navigate to the
Connect System > Accounting
page.
3. Click
Enable RADIUS Accounting
.
4. Enter the Primary Server IP Address or DNS entry for AWMS server.
5. Enter Primary Server Port Number 1813.
6. Enter the Shared Secret (matching the AWMS shared secret).
7. To verify and view the log files on the
Connect Server
proceed to
Monitor > System Log
.
8. To verify and view the log files on AWMS, proceed to
System > Event Log
.
HP ProCurve 700wl Series Secure Access Controllers Integration
A ProCurve security scheme for AWMS has the following prerequisites:
HP 700 version 4.1.1.33 or higher
AWMS version 3.0.4 or higher
Completion of the
AMP
Setup > Radius Accounting
page configurations, as described in
“Integrating a
RADIUS Accounting Server” on page
65
.
Example Network Configuration
In this example, the APs are connected to the Access Controller. The Access Controller routes wireless user traffic
to the Employee Network, while bridging AP management traffic. Each AP is presumed to have a static IP
address.
Perform these steps for HP ProCurve 700wl Series Configuration, allowing AWMS to manage APs through
Control
pages.
1. Log in to the Access Control Server via HTTP with proper credentials.
2. Navigate to
Rights > Identity Profiles
.
3. Select
Network Equipment
.
4. Enter the
Name
,
LAN MAC
and ensure the device is identified as an
Access Points in the Identity Profile
section for all access points in the network.
The Access Points Identity Profile is the default profile for network equipment. Enabling this option instructs
the Access Controller to pass management traffic between the Access Points and the Customer's wired
network.
HP ProCurve 700wl Series Configuration
This procedure enables the sending of client authentication information to AWMS. Perform the following steps
to enable this configuration.
1. Login to the Access Control Server via HTTP with proper credentials.
2. Navigate to the
Rights > Authentication Policies
configuration page.
3. Select
Authentication Services
.
4. Select
New Services
.
Содержание PowerConnect W Airwave 7.1
