Danfoss ADAP-KOOL Drive Скачать руководство пользователя страница 162 | Manualshive

Страница: 162 / 262

background image

21-18 Ext. 1 Feedback [Unit]

Range:

Function:

0.000 Ex-
tPID1Unit*

[-999999.999 - 999999.999 Ex-
tPID1Unit]

Readout of the feedback value for the Closed Loop 1 Controller.

21-19 Ext. 1 Output [%]

Range:

Function:

0 %*

[0 - 100 %]

Readout of the output value for the Closed Loop 1 Controller.

3.16.4 21-2* Closed Loop 1 PID

Configure the Closed Loop 1 PID controller.

21-20 Ext. 1 Normal/Inverse Control

Option:

Function:

[0] *

Normal

Select

Normal

[0] if the output should be reduced when feedback is higher than the reference.

[1]

Inverse

Select

Inverse

[1] if the output should be increased when feedback is higher than the reference.

21-21 Ext. 1 Proportional Gain

Range:

Function:

0.01 N/A* [0.00 - 10.00 N/A]

If (Error x Gain) jumps with a value equal to what is set in par. , the PID controller will try to change the output speed equal to what is set in par.
4-13/4-14, Motor Speed High Limit, but in practice of course limited by this setting.
The proportional band (error causing output to change from 0-100%) can be calculated by means of the formula:

(

1

Proportional

Gain

)

× (

Max

Reference

)

NB!

Always set the desired for par. before setting the values for the PID controller in par. group 20-9*.

21-22 Ext. 1 Integral Time

Range:

Function:

10000.00
s*

[0.01 - 10000.00 s]

Over time, the integrator accumulates a contribution to the output from the PID controller as long
as there is a deviation between the Reference/Setpoint and feedback signals. The contribution is
proportional to the size of the deviation. This ensures that the deviation (error) approaches zero.
Quick response on any deviation is obtained when the integral time is set to a low value. Setting it
too low, however, may cause the control to become unstable.
The value set, is the time needed for the integrator to add the same contribution as the proportional
part for a certain deviation.
If the value is set to 10,000, the controller will act as a pure proportional controller with a P-band
based on the value set in par.20-93

PID Proportional Gain

. When no deviation is present, the output

from the proportional controller will be 0.

21-23 Ext. 1 Differentation Time

Range:

Function:

0.00 s*

[0.00 - 10.00 s]

The differentiator does not react to a constant error. It only provides a gain when the feedback
changes. The quicker the feedback changes, the stronger the gain from the differentiator.

3 Parameter Description

ADAP-KOOL

®

Drive Programming Guide

162

MG.11.N1.02 - VLT

®

is a registered Danfoss trademark

3

«
...
160
161
162
163
164
...
»

Содержание ADAP-KOOL Drive







































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADAP-KOOL Drive

Бренд: Lenze Страницы: 8

Бренд: IEF Werner Страницы: 48

Super-Writemaster SH-S223Q

Бренд: Samsung Страницы: 2

SH-S203B - WriteMaster - DVD±RW

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 5

Бренд: Samsung Страницы: 6

Бренд: Fagor Страницы: 82

ZETADYN 2-ZAdyn4C

Бренд: ZIEHL-ABEGG Страницы: 26

Бренд: Allen-Bradley Страницы: 108

Бренд: Allen-Bradley Страницы: 134

DVD+/-RW Slim External Drive

Бренд: Targus Страницы: 13

Бренд: G-U Страницы: 28

Бренд: BONMET Страницы: 85

iPOS8015 BZ-CAT

Бренд: Technosoft Страницы: 34

Бренд: ZIEHL-ABEGG Страницы: 105

Falk UltraMax Series

Бренд: Rexnord Страницы: 3

Бренд: ICAN Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды