manualshive.com logo in svg

Cisco SRW208MP, Руководство администратора

Administration Manual для Cisco SRW208MP доступен для бесплатного скачивания на manualshive.com. Этот руководство содержит подробные инструкции по управлению и настройке устройства. Получите свой экземпляр сейчас и ознакомьтесь с функциональностью Cisco SRW208MP.

Поделиться
Скачать
background image

Configuring IP Information

Configuring ARP

Cisco Small Business 200 Series Smart Switch Administration Guide 

220

16

-

Local

—A directly-connected network whose prefix is derived from a 

manually-configured switch’s IPv6 address.

-

Dynamic

—The destination is an indirectly-attached (remote) IPv6 subnet 

address. The entry was obtained dynamically via the ND or ICMP 
protocol.

-

Static

—The entry was manually configured by a user.

Configuring ARP

The switch maintains an ARP (Address Resolution Protocol) table for all known 
devices that reside in its directly-connected IP subnets. A directly-connected IP 
subnet is the subnet to which an IPv4 interface of the switch is connected. When 
the switch needs to send/route a packet to a local device, it searches the ARP 
table to obtain the MAC address of the device. The ARP table contains both static 
and dynamic addresses. Static addresses are manually configured and do not age 
out. The switch creates dynamic addresses from the ARP packets it receives. 
Dynamic addresses age out after a configured time. 

NOTE

The IP/MAC address mapping information in the ARP Table is used by the switch to 
forward traffic originated by the switch.

To define the ARP tables:

STEP 1

Click 

IP Configuration

 > 

ARP. 

The 

ARP Table 

page opens.

STEP  2

Enter the parameters.

•

ARP Entry Age Out

—Enter the number of seconds that dynamic addresses 

can remain in the ARP table. A dynamic address ages out after the time it is 
in the table exceeds the ARP Entry Age Out time. When a dynamic address 
ages out, it is deleted from the table, and only returns when it is relearned.

•

Clear ARP Table Entries

—Select the type of ARP entries to be cleared from 

the system.

-

All

—Deletes all of the static and dynamic addresses immediately.

-

Dynamic

—Deletes all of the dynamic addresses immediately.

-

Static

—Deletes all of the static addresses immediately.

Содержание SRW208MP




























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SRW208MP

D-Link Verizon DSL-2750B Setup Manual preview
Verizon DSL-2750B
Бренд: D-Link Страницы: 6
D-Link DIR-857 Quick Installation Manual preview
DIR-857
Бренд: D-Link Страницы: 10
D-Link DSL-2740U Quick Installation Manual preview
DSL-2740U
Бренд: D-Link Страницы: 38
D-Link DXS-3610-54S Quick Installation Manual preview
DXS-3610-54S
Бренд: D-Link Страницы: 38
D-Link DWL-3150 Install Manual preview
DWL-3150
Бренд: D-Link Страницы: 8
D-Link DSS-8+ Manual preview
DSS-8+
Бренд: D-Link Страницы: 22
D-Link DSS-5+ Manual preview
DSS-5+
Бренд: D-Link Страницы: 20
D-Link DSS-24+ Technical Specifications preview
DSS-24+
Бренд: D-Link Страницы: 2
D-Link DSS-24+ Manual preview
DSS-24+
Бренд: D-Link Страницы: 16
D-Link DI-804V Quick Install Manual preview
DI-804V
Бренд: D-Link Страницы: 12
D-Link DIR-615 - Wireless N Router Installation Manual preview
DIR-615 - Wireless N Router
Бренд: D-Link Страницы: 13
D-Link Cobra DSL-5300 User Manual preview
Cobra DSL-5300
Бренд: D-Link Страницы: 124
D-Link Web Smart DES-1210-28P Selection Manual preview
Web Smart DES-1210-28P
Бренд: D-Link Страницы: 6
D-Link 2Voice + 4SW VoIP Router DVG-1402S User Manual preview
2Voice + 4SW VoIP Router DVG-1402S
Бренд: D-Link Страницы: 57
D-Link xStack Storage DSN-4000 Series Manual preview
xStack Storage DSN-4000 Series
Бренд: D-Link Страницы: 23
D-Link Express EtherNetwork DI-604 Brochure preview
Express EtherNetwork DI-604
Бренд: D-Link Страницы: 7
D-Link xStack Storage DSN-4000 Series Cli User'S Manual preview
xStack Storage DSN-4000 Series
Бренд: D-Link Страницы: 97
D-Link SharePort DIR-825 Quick Start Manual preview
SharePort DIR-825
Бренд: D-Link Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды