Cisco ASR 900 Series Скачать руководство пользователя страница 99

Страница: 99 / 310

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

Caveats in Cisco IOS XE 3.7S Releases

Symptom:

The router experiences remote CFM MEP flapping.

Conditions:

Occurs when the router is connected via a CFM xconnect and the link is running a high

traffic rate.

Workaround:

Reduce the rate of traffic.

•

CSCua99096

Symptoms: The

show ima interface

command omits some IMA group information such as

ImaGroupSymmetry.

Conditions: This issue occurs when the

show ima interface

command.

Workaround: There is no workaround.

•

CSCub94462

Symptom:

The router displays object download error messages on the console.

Conditions:

This issue occurs under the following conditions

–

Execute the

mac address sticky

command.

–

Configure 25 incremental MAC addresses and execute the

clean mac-address-table bdomain

command

–

Remove a mac security sticky configuration from an EVC interface.

Workaround:

Avoid issuing the

clear mac-address-table

command when the

mac security sticky

command is applied.

•

CSCuc08397

Symptom:

When IFM is configured on EVC BD, with encapsulation default in the core, the remote

MEPS are not learnt.

Conditions:

This issue is seen when encapsulation default is configured on the core facing side.

Workaround:

There is no workaround.

•

CSCud09142

Symptom:

FP active error messages are seen when the tunnel-tp interface is removed in a

high-availability setup.

Conditions:

This issue is seen after removing tunnel-tp interface.

Workaround:

There is no workaround.

•

CSCud34600

Symptom:

Event hog messages are received when 21k to 25k routes are advertised into MBGP and

exported from one PE to another.

Conditions:

This issue occurs when the redistributing routes range from 21k to 25k routes from

OSFP are moved into MBGP and are exported from one PE to another.

Workaround:

There is no workaround.

•

CSCud90362

Symptom:

the SYNC packets go out quite irregularly when PTP master is configured.

Conditions:

This issue is seen when the router is configured as PTP master.

Workaround:

There is no workaround.

•

CSCue24854

Symptom:

Loss of 70 msec are observed when performing an IM OIR in a remote LFA ring.

Содержание ASR 900 Series























































































































































































































































































































Результаты поиска

Содержание ASR 900 Series

Отзывы:

Cisco ASR 900 Series, Руководство пользователя, Страница: 99 / 310

Результаты поиска

Содержание ASR 900 Series

Отзывы: