Cisco ASR 900 Series Скачать руководство пользователя страница 247

Страница: 247 / 310

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Caveats in Cisco IOS XE 3.9S Releases

Workaround:

There is no workaround.

Further Description:

This depends a lot on the slave and its tolerance levels with respect to SYNC

packets reception and processing. With most of the vendors and Test tools it works today except few.

•

CSCud90890

Symptoms:

Routing over Trunk EFP over Port-channel doesn’t work on member ports associated

with Asic #1

Conditions:

If a Trunk EFP on Port-channel has members on asic#1, routing traffic won’t egress on

those ports

Workaround:

None

•

CSCud92915

Symptoms:

Enable BFD support for IPFRR in 3.8.1

Conditions:

BFD with IPFRR

Workaround:

There is no workaround.

•

CSCud95359

Symptom:

The show policy map command displays an incorrect number of total dropped packets

(total drops).

Conditions:

Occurs when you issue the show policy-map command to display dropped packets on

an interface.

Workaround:

There is no workaround.

•

CSCud96604

Symptoms:

On system reset/reload, all traffic on certain EFPs will not egress

Conditions:

Complete traffic stoppage on certain EFPs

Workaround:

Delete and reconfigure EFPs

•

CSCud96962

Symptoms:

After shut/noshut the mem link interface getting tracebacks - IM Flapping

Conditions:

Configured cfm trunk efp pc -256 session -3.3ms interval after that shut/no shut the

traffic sending interface will hit this issue

Workaround:

Configure very less session 50-100 cfm session

•

CSCud98985

Symptoms:

on executing show tech-support, invalid command errors were detected for a few

commands

Conditions:

on executing show tech-support, invalid command errors were detected for a few

commands

Workaround:

There is no workaround.

•

CSCud99183

Symptoms:

Ctrl protocols stay down, pings fail on booting with scaled ACE/ACL, (ACL

configurations are failing)

Conditions:

it occurs only on reload time

Workaround:

There is no workaround.

•

CSCue00049

Содержание ASR 900 Series























































































































































































































































































































Результаты поиска

Содержание ASR 900 Series

Отзывы:

Cisco ASR 900 Series, Руководство пользователя, Страница: 247 / 310

Результаты поиска

Содержание ASR 900 Series

Отзывы: