Cisco ASR 900 Series Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 310

Cisco ASR 900 Series Скачать руководство пользователя страница 30

2

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

New SoftwareFeatures in Cisco IOS XE Release 3.8(2)S

–

GLC-FE-100FX

–

ONS-XC-10G-EP30.33

–

XFP10GER-192IR-L

–

XFP10GLR-192SR-L

–

XFP-10GZR-OC192LR

For more information about how to configure these SFPs, see:

http://www.cisco.com/en/US/partner/docs/interfaces_modules/transceiver_modules/installation/note/O
L_24246.html

http://www.cisco.com/en/US/partner/products/hw/modules/ps5455/tsd_products_support_series_home
.html

New SoftwareFeatures in Cisco IOS XE Release 3.8(2)S

The IOS XE 3.8(2)S Release for the Cisco ASR 903 Router does not introduce any new software
features.

New Software Features in Cisco IOS XE Release 3.8(1)S

Release 3.8(1) introduces support for the following software features:

•

uRPF Loose Mode—This release introduces support for Unicast Reverse Path Forwarding (uRPF)
Loose mode. For more information about this feature, see

http://www.cisco.com/en/US/docs/ios-xml/ios/sec_data_urpf/configuration/xe-3s/sec-unicast-rpf-l
oose-mode.html

New Software Features in Cisco IOS XE Release 3.8(0)S

Release 3.8(0) introduces support for the following software features:

•

Automatic Protection Switching—This release introduces support for Automatic protection
switching (APS) for link failure protection on SONET networks. For more information, see

http://www.cisco.com/en/US/docs/routers/asr903/feature/guide/APS.html

•

ATM IMA on OC-3 Interfaces—This release introduces support for ATM IMA on the OC-3
interface module. For more information about this feature, see the

Cisco ASR 903 Router Chassis

Configuration Guide, Release 3.8

.

•

BFD Support on TDM interfaces—Release 3.8 introduces support for BFD on TDM interfaces. This
feature does not introduce any new CLI.

•

BFD Support for HSRP—This release extends Bidirectional Forwarding Detection support in order
to send failure notifications using the Hot Standby Router Protocol (HSRP). For more information
about this feature, see

http://www.cisco.com/en/US/products/ps11610/products_installation_and_configuration_guides_l
ist.html

•

BFD Timer Improvements—Release 3.8 introduces support for 3.3ms timers for offloaded IPv4
BFD traffic.

«
...
28
29
30
31
32
...
»

Содержание ASR 900 Series























































































































































































































































































































Отзывы:

Нет отзывов