Cisco ASR 900 Series Скачать руководство пользователя страница 152

Страница: 152 / 310

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

Caveats in Cisco IOS XE 3.7S Releases

•

CSCtz09708

Symptoms:

The router cannot establish a PTP session when configured as a PTP slave device.

Conditions:

Occurs when the router receives PTP packets containing a VPN or VRF label.

Workaround:

There is no workaround.

•

CSCtz54650

Symptoms:

REP flaps intermittently.

Conditions:

Occurs with a hybrid REP configuration containing ports with and without Fast LSL

enabled.

Workaround:

Configure all interfaces with Fast LSL.

•

CSCtz56517

Symptoms:

The router drops MPLS packets with a checksum of 0xFFFF.

Conditions:

Occurs when the ASR 903 is acting as a label disposition edge label switch router

(LSR).

Workaround:

There is no workaround.

•

CSCtz61153

Symptoms:

The ASR 903 does not establish BFD neighbors over port-channel 16.

Conditions:

Occurs when you configure BFD on port-channel 16 between two ASR 903 routers.

Workaround:

Configure BFD on port-channels 1 - 15.

Содержание ASR 900 Series























































































































































































































































































































Результаты поиска

Содержание ASR 900 Series

Отзывы:

Cisco ASR 900 Series, Руководство пользователя, Страница: 152 / 310

Результаты поиска

Содержание ASR 900 Series

Отзывы: