manualshive.com logo in svg

Cisco ASR 900 Series, Руководство пользователя, Страница: 241 / 310

Поделиться
Скачать
Cisco ASR 900 Series Скачать руководство пользователя страница 241

 

45

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

  Caveats in Cisco IOS XE 3.9S Releases

–

ONS-SI-155-I1

Workaround:

 There is no workaround.

•

CSCud27333

Symptom:

 The router crashes continuously.

Conditions:

 Occurs when you issue an interface module reset (OIR) while the standby RSP is 

booting.

Workaround:

 Do not issue an interface module reset (OIR) while the standby RSP is booting.

•

CSCud28982

Symptom:

 The router does not process egress CoS marking on an Ethernet service instance.

Conditions:

 Occurs when you configure QoS on an Ethernet service instance that is a member of a 

bridge-domain and uses dot1q encapsulation.

Workaround:

 There is no workaround.

•

CSCud29479

Symptom:

 The router stops applying QoS configurations.

Conditions:

 Occurs under the following conditions:

–

An Ethernet interface is configured with a single service instance

–

A QoS policy is attached to the service instance 

–

The QoS policy contains a single class containing a 

match efp

 statement.

–

You reset the interface to the default configuration.

Workaround:

 There is no workaround.

•

CSCud30806

Symptoms:

 Policy with class map match-all with prec 1 and prec 2 is accepted for WRED.

Conditions: 

match-all should not accept 2 prec values class-map match-all prec1_2 match 

precedence 1 match precedence 2 

Workaround:

 N/A

•

CSCud33298

Symptom:

 The router crashes.

Conditions:

 Occurs when the peer device shuts down.

Workaround:

 There is no workaround.

•

CSCud33906

Symptom: 

Equal Cost Multipath (ECMP) loopback does not function properly.

Conditions:

 Occurs when a port-channel link dynamically assigned as an ECMP path.

Workaround:

 There is no workaround.

•

CSCud34346

Symptom:

 Nile manager crashes with the ECMP path when IPv4 scale is exceeded.

Conditions:

 This symptom occurs when scale is exceeded with the ECMP path.

Workaround:

 Do not allow the user to exceed the supported IPv4 route scale with ECMP. 

•

CSCud34600

Содержание ASR 900 Series























































































































































































































































































































Отзывы:

Нет отзывов