manualshive.com logo in svg

Cisco ASR 900 Series, Руководство пользователя, Страница: 110 / 310

Поделиться
Скачать
Cisco ASR 900 Series Скачать руководство пользователя страница 110

 

22

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter  

  Caveats in Cisco IOS XE 3.7S Releases

Workaround:

 There is no workaround.

  •

CSCud38115

Symptom:

 OSPF connections flap and drop traffic for approximately 20 seconds

Conditions:

 This issue occurs during stateful switchover (SSO).

Workaround:

 There is no workaround. 

  •

CSCue07502

Symptom:

 A crash is observed after completing ISSU. The F0/F1 are getting stuck in init state.

Conditions:

 This issue occurs after completing ISSU.

Workaround:

 Reload the router.

  •

CSCue24854

Symptom:

 Performing an IM OIR in a remote LFA ring reports a loss of 70 ms.

Conditions:

 This issue occurs during a soft OIR of the IM.

Workaround:

 Perform a hard OIR for a loss less than 50 ms.

  •

CSCue87571

Symptom:

 GLC-ZX-SM-RGD and GLC-LX-SM-RGD rapid SFP OIR causes ipprom to fail.

Conditions:

 This issue occurs after rapid SFP OIR.

Workaround:

 Perform each OIR with a delay of 30-40 seconds between the OIR. Reload the IM to 

recover the port.

Содержание ASR 900 Series























































































































































































































































































































Отзывы:

Нет отзывов