Cisco ASR 900 Series Скачать руководство пользователя страница 108

Страница: 108 / 310

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

Caveats in Cisco IOS XE 3.7S Releases

•

CSCuh16011

Symptom:

FMAN-FP crashes when you perform ab IM OIR.

Conditions:

This issue is observed when you perform multiple IM OIRs with around 65 BFD

sessions.

Workaround:

Reload the router.

•

CSCuh27117

Symptom:

Traffic loss of about six to eight seconds is observed when you perform an SSO.

Conditions:

This issue is observed when you perform the switchover before IM OIR or the interface

flaps.

Workaround:

There is no workaround

•

CSCuh77762

Symptom:

The TenGigabitEthernet port operates at one gigabit speeds in WAN-PHY mode on

Cisco ASR 903 Routers. This leads to a huge amount of output drop.

Conditions:

This issue is observed if a QoS policy is configured on the TenGigabitEthernet

interface.

Workaround:

There is no workaround.

•

CSCuh86102

Symptom:

The interface stops forwarding traffic.

Conditions:

This issue is observed when the TenGigabitEthernet interface is in WAN-PHY mode

and R0 is active.

Workaround:

Use R1

•

CSCuh92939

Symptom:

Replacing the copper SFP with SFP causes traffic drop after SSO is performed

Conditions:

This issue occurs after replacing the copper SFP with the fiber SFP.

Workaround:

Perform an IM OIR.

•

CSCuh94841

Symptom:

10 Gigabit Ethernet interface flaps without trigger causing traffic to switch to protected

label-switched path (LSP).

Conditions:

This issue occurs when the script is run for continuous SSO.

Workaround:

There is no workaround.

•

CSCui08978

Symptom:

Crash observed on the router.

Conditions:

This issue occurs when shutdown followed by a no shutdown is performed on the

physical interfaces.

Workaround:

There is no workaround.

Содержание ASR 900 Series























































































































































































































































































































Результаты поиска

Содержание ASR 900 Series

Отзывы:

Cisco ASR 900 Series, Руководство пользователя, Страница: 108 / 310

Результаты поиска

Содержание ASR 900 Series

Отзывы: