Cisco ASR 900 Series Скачать руководство пользователя страница 204

Страница: 204 / 310

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Caveats in Cisco IOS XE 3.9S Releases

Conditions:

This issue occurs in an mVPN network on exceeding core multicast distribution tree

(MDT) scale of 1K with more than 20 virtual routing and forwarding (VRFs) on a flap access
interface of a PE Router.

Workaround:

Do not exceed more than 1K core MDT scale Work around for a crash is unavailable.

•

CSCuf02007

Symptom:

Continuous SEMHOG is seen on the router console with incremental sync failure and

IOMD crashes on OC-3 IM.

Conditions:

Router receives continuous SEMHOG for multiple processes.

Workaround:

There is no workaround.

•

CSCuf06001

Symptom:

When TCAM limit is reached, statistics do not work accurately.

Conditions:

This issue occurs when the TCAM entries exceed the limit during dynamic

modification of service-policy.

Workaround:

There is no workaround.

•

CSCuf43992

Symptom:

The router crashes if you configure local span.

Conditions:

This issue is observed when you configure local span on the router.

Workaround:

Use another Encapsulated Remote Switched Port Analyzer (ERSPAN) configuration

to work as local span with source and destination ERSPAN session configured in one router.

•

CSCuf45656

Symptom:

Cisco ASR 903 Router crashes with segmentation fault.

Conditions:

This issue occurs during multicast convergence on EFP’s configured with split horizon.

Workaround:

There is no workaround.

•

CSCuf53527

Symptom:

Class of Service (CoS) inner value gets copied into the CoS value.

Conditions:

This issue occurs when configuring Q-in-Q without rewrite service instance.

Workaround:

To ensure CoS inner value does not get copied, apply QoS policy-map.

•

CSCuf65301

Symptom:

Micro flaps observed on the router.

Conditions:

This issue is seen when system is kept idle for hours.

Workaround:

There is no workaround.

•

CSCuf79397

Symptom:

F1 is stuck in init state after the standby RSP reloads.

Conditions:

This issue occurs on a reload or OIR of the standby RSP.

Workaround:

Reload the standby RSP again.

•

CSCuf81085

Symptom:

After you use the

shutdown

and

no shutdown

commands on the controller of PE, IMA

VCs go down.

Conditions:

This issue is observed after using the

shutdown

and

no shutdown

commands on the

OC3 controller on PE routers.

Содержание ASR 900 Series























































































































































































































































































































Результаты поиска

Содержание ASR 900 Series

Отзывы:

Cisco ASR 900 Series, Руководство пользователя, Страница: 204 / 310

Результаты поиска

Содержание ASR 900 Series

Отзывы: