manualshive.com logo in svg

Cisco ASR 900 Series, Руководство пользователя, Страница: 167 / 310

Поделиться
Скачать
Cisco ASR 900 Series Скачать руководство пользователя страница 167

 

15

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

  Caveats in Cisco IOS XE 3.8S Releases

•

CSCud76957

Symptom:

 Traffic gets dropped during egress when service instance is configured.

Conditions:

 This issue occurs when service instance is configured.

Workaround:

 Unconfigure the service instance and reconfigure it again.

•

CSCud90890

Symptom:

 Routing over Trunk EFP over port-channel does not work on member ports associated 

with ASIC #1.

Conditions:

 This issue occurs when a Trunk EFP on port-channel has members on ASIC#1, the 

routing traffic does not egress on those ports.

Workaround:

 There is no workaround.

•

CSCud90955

Symptom:

 The following console messages are seen whenever BFD session is created or modified.

Jan  3 06:34:52.481: %HANDOFF_FUD-6-QDR_MULTI_BIT_ERROR_START: SIP1: nile_mgr:  

Handoff FPGA could encounter MBE,  check at start of create update BFD session

Jan  3 06:34:52.481: %HANDOFF_FUD-6-QDR_MULTI_BIT_ERROR_END: SIP1: nile_mgr:  Handoff 

FPGA could encounter MBE, check at end of create update BFD session

Jan  3 06:34:53.167: %HANDOFF_FUD-6-QDR_MULTI_BIT_ERROR_START: SIP0: nile_mgr:  

Handoff FPGA could encounter MBE,  check at start of create update BFD session

Jan  3 06:34:53.167: %HANDOFF_FUD-6-QDR_MULTI_BIT_ERROR_END: SIP0: nile_mgr:  Handoff 

FPGA could encounter MBE, check at end of create update BFD session

Conditions:

 This issue occurs when BFD sessions are created or modified.

Workaround:

 There is no workaround. This issue has no service impact.

•

CSCud96604

Symptom: 

On system reset or reload, all traffic on certain Ethernet Flow Point (EFP)s do not egress.

Conditions:

 This issue occurs when traffic completely stops on certain EFPs.

Workaround:

 Delete and reconfigure EFPs.

•

CSCue00049

Symptom:

 Classification does not work properly with non-matching traffic when IP ACL is used.

Conditions:

 This issue occurs only for class-based ACL match. The ACL class are classified 

properly and other classes based on DSCP or class-default do not work

Workaround:

 There is no workaround. 

•

CSCue10037

Symptom:

 Crash observed on the router.

Conditions:

 This issue after when CFM is offloaded and MEPs with 3.3ms were scaled on 

port-channel with Trunk EFP. This issue occurs after 

shutdown

 command followed by a 

no 

shutdown

 command is executed on the member links of port-channel.

Workaround: 

Configure around 50-100 CFM sessions.

•

CSCue11444

Symptom:

 Split horizon configurations does not clear with Layer2 multicast packets.

Conditions:

 This issue occurs when Ethernet Flow Point (EFP)s with split-horizon are configured.

Workaround:

 Perform a shutdown followed by no shutdown. Configure EFP first before moving 

into split-horizon group.

Содержание ASR 900 Series























































































































































































































































































































Отзывы:

Нет отзывов