Cisco ASR 900 Series Скачать руководство пользователя страница 65

Страница: 65 / 310

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter Restrictions and Caveats in Cisco IOS XE 3.6S Releases

Caveats in Cisco IOS XE 3.6S Releases

Conditions:

Occurs when shaping is configured on class-default

Workaround:

Configure shaping on user defined class

•

CSCtw76473

Symptoms:

The router displays packet drops on some VPLS pseudowire virtual circuits (VCs) on

the disposition side.

Conditions:

Occurs under the following conditions: -The core network is running MPLS-TP tunnels

-There is an SSO switchover on the remote end or an LDP neighbor reset on the peer end.

Workaround:

There is no workaround.

•

CSCty45463

Symptoms:

The router stops passing VPLS unicast traffic.

Conditions:

Occurs after you reload the router while it is passing VPLS unicast traffic.

Workaround:

Perform one of the following actions:

–

Clear the mac-address table on the affected virtual circuit (VC)

–

Stop VPLS traffic until the MAC address table is cleared, then resume VPLS traffic.

•

CSCty51990

Symptoms:

The router may crash or restart; the console displays a SW_WDOG: expired message.

Conditions:

Occurs under the following conditions:

–

The router is configured with 63 or more instances of a unique EVC configured with a unique
bridge domain interface (BDI).

–

The router is sending IGMP joins to one multicast group.

–

You perform a shutdown/no shutdown on the interface sending IGMP join messages.

–

You perform an OIR on the router.

Workaround:

There is no workaround.

•

CSCty70119

Symptoms:

Port shaper rate changes do not take effect.

Conditions:

Occurs when QoS policies attached to EVCs on an interface do not include a shaper

configuration; the issue does not occur on EFP policies that include a shaper in a class.

Workaround:

Include a shaper in one class of the EFP policy.

•

CSCtz20087

Symptoms:

The router applies the class-default QoS policy to all outgoing traffic.

Conditions:

Occurs under the following conditions: -You configure multiple egress QoS policies on

a Gigabit Ethernet interface. -You configure a multilink interface with no ingress QoS policy

Workaround:

There is no workaround.

•

CSCua10683

Symptoms:

The router performs an RSP switchover instead of a thermal shutdown.

Conditions:

Occurs when the

facility-alarm critical exceed-action shutdown

command is in the

running configuration and some sensors go into a critical condition as indicated by the

show

environment all

show facility-alarm status

commands.

Workaround:

There is no workaround.

Содержание ASR 900 Series























































































































































































































































































































Результаты поиска

Содержание ASR 900 Series

Отзывы:

Cisco ASR 900 Series, Руководство пользователя, Страница: 65 / 310

Результаты поиска

Содержание ASR 900 Series

Отзывы: