Cisco ASR 900 Series Скачать руководство пользователя страница 239

Страница: 239 / 310

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Caveats in Cisco IOS XE 3.9S Releases

•

CSCuc92953

Symptom:

The RSP crashes.

Conditions:

Occurs under the following conditions:

–

You configure Protocol-Independent Multicast-Sparse Mode (PIM-SM) with a static
rendezvous point (RP).

–

You create an EVC port channel on the access side with one member link

–

You create bridge domain interfaces (BDIs) with 1:1 mapping between EVCs and
bridge-domains.

–

You use the BDIs to send IGMP v2 static join messages to a single multicast group

–

On the remote device, you create 150 EFPs and map them to the BDIs.

–

You initiate multicast traffic.

–

You set the EFPs to the default configuration and add them to the existing port-channel

The router crashes.

Workaround:

There is no workaround.

•

CSCuc93985

Symptom:

The router initiates an Automatic Protection Switching (APS) switchover during a high

availability (HA) stateful switchover (SSO).

Conditions:

Occurs during an HA SSO with single router APS (SR-APS).

Workaround:

There is no workaround.

•

CSCuc95716

Symptom:

FPGA software for the OC-3 interface module is not bundled with the XE 3.8 image.

Conditions:

Occurs when upgrading FPGA on the OC-3 interface module.

Workaround:

Manually upgrade the OC-3 FPGA.

•

CSCud01855

Symptoms:

APS switchover may occasionally lead to inconsistent/incorrect APS states with CEM

config.

Conditions:

Seen when APS is configured with CEM/ATM on IM-4OS on ASR903. Caused due to

notifications not being correctly sent to CEM subsystem.

Workaround:

No workaround.

•

CSCud01908

Symptom:

Debug commands show pending objects on the Forwarding Manager (FMAN) on the

forwarding processor (FP), indicating a failure to download configurations from the Route Switch
Processor (RSP) to the data plane (DP).

Conditions:

Occurs when you apply a QoS shaping configuration at a high scale.

Workaround:

Delete the QoS policies and remove the QoS configuration from the interface.

•

CSCud04407

Symptom:

The router displays the following console error message:

Error - packet with

unsupported linktype 3

Conditions:

Occurs when the router is passing traffic over the OC-3 interface module.

Workaround:

There is no workaround.

Содержание ASR 900 Series























































































































































































































































































































Результаты поиска

Содержание ASR 900 Series

Отзывы:

Cisco ASR 900 Series, Руководство пользователя, Страница: 239 / 310

Результаты поиска

Содержание ASR 900 Series

Отзывы: