Cisco ASR 900 Series Скачать руководство пользователя страница 277

Страница: 277 / 310

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

Caveats in Cisco IOS XE 3.10S Releases

•

CSCud55695

Symptom:

When you apply a QoS policy with a port level class-default configuration containing a

shaper value to a serial interface, the router applies the shaper value to the channel-level PIR for all
serial interfaces on the IM.

Conditions:

This issue is observed when you apply a QoS policy with a port level class-default

configuration containing a shaper value to a serial interface.

Workaround:

Add a dummy class-default level at the top of the policy and apply the shaper as a

child policy.

•

CSCud55799

Symptom:

Multiple priority commands are accepted per policy.

Conditions:

This issue is observed when you have a policy map with priority configured in one of

its classes. Add another class with policer first and with priority.

Workaround:

There is no work around.

•

CSCud56364

Symptom:

Convergence time for POS links for RSP SSO is about four to seven seconds.

Conditions:

This issue is observed when all four POS links are created on OC-3 IM. This issue is

not observed on port 0 of OC-3 IM.

Workaround:

There is no work around.

•

CSCud61551

Symptom:

The serial number of the RSP in slot 1 is sometimes not displayed in the

show inventory

command output.

Conditions:

This issue is sometimes observed in the

show inventory

command output.

Workaround:

Reload the router.

•

CSCud64129

Symptom:

The router displays command options to configure control-plane policing, which is not

supported.

Router(config)#

control-plane

Router(config-cp)#

service-policy ?

input Assign policy-map to the input of an interface

output Assign policy-map to the output of an interface

Conditions:

This issue is observed when you attempt to configure control plane policing to restrict

traffic by the CPU.

Workaround:

There is no workaround. This feature is not supported.

•

CSCud71286

Symptom:

Configuration synchronization failure is noticed on the interfaces.

Conditions:

This issue is observed when you disable autonegotiation and configure the interface

speed as 100 or 1000.

Workaround:

There is no workaround. There is no impact on functionality.

Содержание ASR 900 Series























































































































































































































































































































Результаты поиска

Содержание ASR 900 Series

Отзывы:

Cisco ASR 900 Series, Руководство пользователя, Страница: 277 / 310

Результаты поиска

Содержание ASR 900 Series

Отзывы: