Cisco ASR 900 Series Скачать руководство пользователя страница 226 | Manualshive

Страница: 226 / 310

Cisco ASR 900 Series Скачать руководство пользователя страница 226

30

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Caveats in Cisco IOS XE 3.9S Releases

Conditions:

Punt/inject keepalives are missed and we are not holding a TTY while writing to

punt/inject log file.

Workaround:

none

•

CSCue96886

Symptoms:

Complete MAC Address space is not available on the RSP

Conditions:

Removing the Service instance with the MAC Addresses learnt on the BD.

Workaround:

Reload the Router is only workaround.

•

CSCue97114

Symptoms:

Shut down the trunk efp in core side, meps are learnt for UP MEP

Conditions:

Configured UP Mep evc bd (core side trunk efp) when i shut the trunk efp in core

remote meps are learnt for UP MEP.

Workaround:

Configure evc bd in core side

•

CSCuf05090

Symptoms:

Standby will be resetting continuously with running config sync failure.

Conditions:

Downgrade all IMs and take the IMS out of slot.After booting up with XE39 image , insert IMs one
by one. While upgrade was happening , this issue happened.Im got crashed and stanby was resetting
continuously with SYNc failed.

Workaround:

Reload the box completely.

•

CSCuf20275

Symptoms:

On interoperating with an ASR901 router, BFD sessions may flap as the ASR903 router

may some times not send BFD control messages.

Conditions:

With around 200 global IPv4 prefixes, BFD session running in software with echo OFF

and seen even without any data traffic.

Workaround:

There is no work-around known as yet.

•

CSCuf44077

Symptoms:

show interface output is showing wrong speed values after sso

Conditions:

when we use the 100M SFP’s

Workaround:

There is no functionality impact because of this. HW module reset will resolve this.

•

CSCuf56723

Symptoms:

Interface LED glows green with shut.

Conditions:

After SSO

Workaround:

No workaround.

•

CSCuf60346

Symptoms:

IOMd Crash On Performing SSO Switchover With Interfaces Shut

Conditions:

Have ATM/IMA interfaces shut. Perform switchover and notice IOMd crash on new

Active

Workaround:

No workaround

•

CSCuf64404

«
...
224
225
226
227
228
...
»

Содержание ASR 900 Series























































































































































































































































































































Отзывы:

Нет отзывов