Cisco ASR 900 Series Скачать руководство пользователя страница 165

Страница: 165 / 310

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

Caveats in Cisco IOS XE 3.8S Releases

•

CSCud13242

Symptom:

The Cisco ASR 903 router does not display an alarm when nV satellite authentication

fails.

Conditions:

This issue occurs when the ASR 9000 and ASR 903 are in an nV satellite configuration

and the routers are configured with a different serial-number value.

Workaround:

There is no workaround.

•

CSCud26812

Symptom:

The router CLI does not display some SFP PIDs.

Conditions:

This issue occurs when you install one of the following SFPs in the router:

–ONS-SI-155-L2

–ONS-SI-155-L1

–ONS-SI-155-I1

Workaround:

There is no workaround.

•

CSCud29479

Symptom:

The router stops applying QoS configurations.

Conditions:

Occurs under the following conditions:

–An Ethernet interface is configured with a single service instance

–A QoS policy is attached to the service instance

–The QoS policy contains a single class containing a match EFP statement.

–You reset the interface to the default configuration.

Workaround:

There is no workaround.

•

CSCud30806

Symptom:

The router accepts a QoS WRED configuration containing

match-all

configurations for

two different

prec

values, which is not supported.

Conditions:

This issue occurs when you configure a policy with a class-map containing

match-al

configurations for two different

prec

values.

Workaround:

There is no workaround.

•

CSCud34346

Symptom:

The router crashes with multiple ECMP paths configured.

Conditions:

The issue can occur when:

–The router is configured with multiple ECMP paths.

–MPLS IP is not enabled on one of the ECMP paths.

Workaround:

There is no workaround.

•

CSCud38038

Symptom:

The router records incorrect delay measurements after a reload.

Conditions:

This issue occurs under the following conditions:

–You configure Delay Measurement Message (DMM) on a port-channel interface.

–The port-channel member links are on different interface modules (IMs).

–You reload the router.

Содержание ASR 900 Series























































































































































































































































































































Результаты поиска

Содержание ASR 900 Series

Отзывы:

Cisco ASR 900 Series, Руководство пользователя, Страница: 165 / 310

Результаты поиска

Содержание ASR 900 Series

Отзывы: