Cisco ASR 900 Series Скачать руководство пользователя страница 119

Страница: 119 / 310

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

Caveats in Cisco IOS XE 3.7S Releases

•

CSCud40930

Symptom:

Some interfaces within a bridge-domain are unable to send outbound L3 multicast

traffic.

Conditions:

Occurs when the bridge-domain contains EFP interfaces, some of which are on a

port-channel. The issue can also occur after a router reload.

Workaround:

Issue a

shutdown

no shutdown

on the BDI interface.

•

CSCud44768

Symptom:

Multilink bundles and member links flap when passing traffic.

Conditions:

Occurs under the following conditions:

–

You configure more than 210 MLPPP bundles with one member link per bundle or 16 bundles
with 16 member links each.

–

The line is operating at a 64 or 128 byte line rate

Workaround:

There is no workaround.

•

CSCud44942

Symptom:

The router does not learn remote Connectivity Fault Management (CFM) Maintenance

Endpoint (MEPs).

Conditions:

Occurs when you configure a MEP on an interface.

Workaround:

There is no workaround.

•

CSCud49980

Symptom:

The router does not learn remote Connectivity Fault Management (CFM) Maintenance

Endpoint (MEPs).

Conditions:

Occurs when you configure CFM MEPs on carrier edge (CE) routers and VPLS on

provider edge (PE) routers.

Workaround:

Create an EVC bridge-domain running CFM on the PE router and enable a virtual

forwarding interface (VFI) on the bridge-domain.

•

CSCud50851

Symptom:

The router experiences flapping on REP connections.

Conditions:

Occurs when you enable MAC limiting at a high scale and the set of MAC addresses

changes continuously.

Workaround:

Disable MAC limiting.

•

CSCud50944

Symptom:

The router drops traffic on an MLPPP bundle.

Conditions:

Occurs following a reload while the router is passing traffic close to the line rate. The

issue occurs less frequently with lower traffic rates.

Workaround:

Issue a

shutdown

no shutdown

on multilink interface.

•

CSCud55377

Symptom:

The router crashes.

Conditions:

Occurs when you configure offloaded CFM for xconnect sessions at a high scale.

Workaround:

There is no workaround.

Содержание ASR 900 Series























































































































































































































































































































Результаты поиска

Содержание ASR 900 Series

Отзывы:

Cisco ASR 900 Series, Руководство пользователя, Страница: 119 / 310

Результаты поиска

Содержание ASR 900 Series

Отзывы: