Cisco ASR 900 Series Скачать руководство пользователя страница 104

Страница: 104 / 310

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

Caveats in Cisco IOS XE 3.7S Releases

•

CSCue77596

Symptom:

CoS value gets wrongly marked for a qinq packet.

Conditions:

This issue occurs when a service instance with dot1q encapsulation and

no rewrite

configured on the interface; The policy map attached in the ingress has marking configured.

Workaround:

There is no workaround.

•

CSCue80866

Symptom:

Label exhaustion message is seen with scale match vlan and match PHB policy;

Classification fails to work.

Conditions:

This issue occurs with TEFP with range of BDs that have match VLANs of the

corresponding BD and a child policy to match prec/cos.

Workaround:

There is no workaround.

•

CSCue83621

Symptom:

Policy-map stops working on removing class default class dynamically.

Conditions:

This issue occurs when policy-map is attached to target and class-default of top level

is deleted dynamically.

Workaround:

Detach and reattach the policy-map on target.

•

CSCue91533

Symptom:

Traffic through VPLS pseudowire is flooded due to MAC aging.

Conditions:

This symptom is observed when bridge descriptor index (internal index) assigned to

MAC address exceeds 20480.

Workaround:

There is no workaround.

•

CSCue94811

Symptom:

Process crash on standby router would not generate a core file.

Conditions:

This issue occurs under normal conditions.

Workaround:

There is no workaround.

•

CSCuf02518

Symptom:

IPv4 traffic gets affected on IPv6 ACL applied interface.

Condition:

This issue occurs when both If IPv4 and IPv6 ACLs share the same label, the IPv4 traffic

on the interface on which IPv6 ACL is applied is impacted.

Workaround:

There is no workaround.

•

CSCuf43992

Symptom:

The router crashed with local span configuration.

Conditions:

This issue occurs with local span configuration.

Workaround: Configure erspan configuration with source and destination erspan sessions in the
router.

•

CSCuf51509

Symptom:

WRED counters for CS0 does not work in

show policy-map interface

command.

Conditions:

This issue is observed when

show policy-map interface

command is executed.

Workaround:

There is no workaround.

Содержание ASR 900 Series























































































































































































































































































































Результаты поиска

Содержание ASR 900 Series

Отзывы:

Cisco ASR 900 Series, Руководство пользователя, Страница: 104 / 310

Результаты поиска

Содержание ASR 900 Series

Отзывы: