Cisco ASR 900 Series Скачать руководство пользователя страница 256 | Manualshive

Страница: 256 / 310

Cisco ASR 900 Series Скачать руководство пользователя страница 256

2

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

Caveats in Cisco IOS XE 3.10S Releases

Caveats in Cisco IOS XE 3.10S Releases

Caveats describe unexpected behavior. Severity 1 caveats are the most serious caveats. Severity 2 caveats
are less serious. Severity 3 caveats are moderate caveats and only select severity 3 caveats are included
in this chapter.

This section describes caveats in Cisco IOS XE 3.10S releases. The following information is provided
for each caveat:

•

Symptom—A description of what is observed when the caveat occurs.

•

Conditions—The conditions under which the caveat has been known to occur.

•

Workaround—Solutions, if available, to counteract the caveat.

The

Dictionary of Internetworking Terms and Acronyms

contains definitions of acronyms that are not

defined in this document:

http://docwiki.cisco.com/wiki/Category:Internetworking_Terms_and_Acronyms_(ITA)

Bug Search Tool

The Caveats section only includes the bug ID and a short description of the bug. For details on the
symptoms, conditions, and workaround for a particular bug you must use the Bug Search Tool.

Use the following link to access the tool:

https://tools.cisco.com/bugsearch/search.

You will be prompted to log into Cisco.com. After successful login, the Bug Search Tool page opens.
Use the Help link in the Bug Search Tool to obtain detailed help.

Caveats

The following sections describe the open and resolved caveats in 3.10S Releases:

•

Resolved Caveats—Cisco IOS XE Release 3.10.(2)aS, page 13-2

•

Open Caveats—Cisco IOS XE Release 3.10.2S, page 13-3

•

Resolved Caveats—Cisco IOS XE Release 3.10.2S, page 13-4

•

Open Caveats—Cisco IOS XE Release 3.10.1S, page 13-9

•

Resolved Caveats—Cisco IOS XE Release 3.10.1S, page 13-12

•

Open Caveats—Cisco IOS XE Release 3.10S, page 13-17

•

Resolved Caveats—Cisco IOS XE Release 3.10S, page 13-20

Resolved Caveats—Cisco IOS XE Release 3.10.(2)aS

This section documents the issues that have been resolved in Cisco IOS XE Release 3.10.(2)aS.

•

CSCul06921

Symptom: Port-channel member-links flaps are observed on the router.

Conditions: This issue is seen on router switchover.

Workaround: There is no workaround.

«
...
254
255
256
257
258
...
»

Содержание ASR 900 Series























































































































































































































































































































Отзывы:

Нет отзывов