Cisco ASR 900 Series Скачать руководство пользователя страница 80

Страница: 80 / 310

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter Restrictions and Caveats in Cisco IOS XE 3.6S Releases

Caveats in Cisco IOS XE 3.6S Releases

•

CSCty34812

Symptoms:

The router experiences traffic loss for between 10 and 50 seconds during RSP

switchover.

Conditions:

Occurs when you perform an RSP switchover on a router with a ten gigabit Ethernet

interface module.

Workaround:

There is no workaround.

•

CSCty35365

Symptoms:

The router drops traffic passing across ATM MPLS layer 2 virtual circuits (VCs).

Conditions:

Occurs when you increase the scale above 100 VCs.

Workaround:

There is no workaround.

•

CSCty37479

Symptoms:

The line protocol repeatedly drops (flaps) on serial interfaces.

Conditions:

Occurs when you configure HDLC or PPP on serial interfaces on the A900-IMA4OS

or A900-IMA16D interface modules when the router is passing high traffic volumes.

Workaround:

Configure the

no keepalive

command on serial interfaces.

•

CSCty38638

Symptoms:

The router cannot download the ACL database.

Conditions:

Occurs when the router is configured with an ACL containing more than 400 access

control entries (ACEs).

Workaround:

There is no workaround.

•

CSCty39033

Symptoms:

Interface modules stop passing traffic during an RSP switchover.

Conditions:

Occurs when the router switches over to the standby RSP while traffic is passing on

interface modules.

Workaround:

There is no workaround.

•

CSCty41536

Symptoms:

The router crashes during when SNMP uses a high percentage of CPU for an extended

period.

Conditions:

Occurs when SNMP is running the background with an average of 50% CPU utilization

for more than 8 hours.

Workaround:

Reduce the load on the CPU using SNMP poll and SNMP walk.

•

CSCty42336

Symptoms:

BFD sessions flap on the router.

Conditions:

Occurs when the router is running IP BFD sessions in echo mode with 64 200ms X3

timers.

Workaround:

There is no workaround.

•

CSCty42867

Symptoms:

The router crashes.

Conditions

: Occurs when you apply traffic soaking to the router with L2VPN services configured.

Workaround

: There is no workaround.

Содержание ASR 900 Series























































































































































































































































































































Результаты поиска

Содержание ASR 900 Series

Отзывы:

Cisco ASR 900 Series, Руководство пользователя, Страница: 80 / 310

Результаты поиска

Содержание ASR 900 Series

Отзывы: