manualshive.com logo in svg

Cisco ASR 900 Series, Руководство пользователя, Страница: 177 / 310

Поделиться
Скачать
Cisco ASR 900 Series Скачать руководство пользователя страница 177

 

25

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

  Caveats in Cisco IOS XE 3.8S Releases

•

CSCuc58371

Symptom:

 Some links do not become active on the OC-3 interface module.

Conditions:

 Occurs on the OC-3 interface module (IM) configured at a high scale after you perform 

a multiple soft OIRs on the IM. The issue occurs frequently with SONET framing.

Workaround:

 You can use the following workarounds:

–

Apply a 

shutdown

/

no shutdown

 to the OC-3 controller.

–

Re-apply the PDH configuration.

–

Add and remove a loopback configuration on the PDH.

Add and remove a loopback configuration on the OC-3 controller. 

•

CSCuc64654

Symptom:

 The router is unable to ping the remote customer edge (CE) router.

Conditions:

 Occurs when the router is acting as a provider edge (PE) device and is connected to the 

remote PE using dual loopback interfaces for peering with iBGP sessions.

Workaround:

 Use a single loopback interface. Use the same loopback interface for IPv4 and 

VPNv4 address families. 

•

CSCuc66393

Symptom:

 The router loses OC-3 interface configurations after an ISSU upgrade.

Conditions:

 Occurs on OC-3 serial and POS interfaces after an ISSU software upgrade.

Workaround:

 There is no workaround.

•

CSCuc68462

Symptom:

 The router drops PTP traffic.

Conditions:

 The issue occurs occasionally when you configure PTP slave clock to receive 

VLAN-tagged traffic.

Workaround:

 There is no workaround.

•

CSCuc71723

Symptom:

 The router erroneously accepts a service-policy configuration on a CEM interface and 

displays it within the running configuration.

Conditions:

 Occurs when you configure a service-policy on a CEM interface.

Workaround:

 There is no workaround.

•

CSCuc85721

Symptom:

 The router crashes.

Conditions:

 Occurs under the following conditions:

–

MR-APS is configured on serial interfaces on the OC-3 interface module

–

The router is configured with a high number of serial interfaces

–

You reset an interface module or reload the router.

Workaround:

 There is no workaround.

•

CSCuc90008

Symptom: 

The OC-3 controller stops passing traffic.

Conditions: 

Occurs after you reset the facing interface on the CE device.

Содержание ASR 900 Series























































































































































































































































































































Отзывы:

Нет отзывов